xxx

DebugConfig/Target_1_STM32F103C8_1.0.0.dbgconf

+// <<< Use Configuration Wizard in Context Menu >>>
+// <h> Debug MCU Configuration
+//   <o0.0>    DBG_SLEEP
+// <i> Debug Sleep Mode
+// <i> 0: (FCLK=On, HCLK=Off) FCLK is clocked by the system clock as previously configured by the software while HCLK is disabled
+// <i> 1: (FCLK=On, HCLK=On) HCLK is fed by the same clock that is provided to FCLK
+//   <o0.1>    DBG_STOP
+// <i> Debug Stop Mode
+// <i> 0: (FCLK=Off, HCLK=Off) Clock controller disables all clocks
+// <i> 1: (FCLK=On, HCLK=On) FCLK and HCLK are provided by the internal RC oscillator which remains active
+//   <o0.2>    DBG_STANDBY
+// <i> Debug Standby Mode
+// <i> 0: (FCLK=Off, HCLK=Off) The whole digital part is unpowered.
+// <i> 1: (FCLK=On, HCLK=On) Digital part is powered and FCLK and HCLK are provided by the internal RC oscillator which remains active
+//   <o0.8>    DBG_IWDG_STOP
+// <i> Debug independent watchdog stopped when core is halted
+// <i> 0: The watchdog counter clock continues even if the core is halted
+// <i> 1: The watchdog counter clock is stopped when the core is halted
+//   <o0.9>    DBG_WWDG_STOP
+// <i> Debug window watchdog stopped when core is halted
+// <i> 0: The window watchdog counter clock continues even if the core is halted
+// <i> 1: The window watchdog counter clock is stopped when the core is halted
+//   <o0.10>   DBG_TIM1_STOP
+// <i> Timer 1 counter stopped when core is halted
+// <i> 0: The clock of the involved Timer Counter is fed even if the core is halted
+// <i> 1: The clock of the involved Timer counter is stopped when the core is halted
+//   <o0.11>   DBG_TIM2_STOP
+// <i> Timer 2 counter stopped when core is halted
+// <i> 0: The clock of the involved Timer Counter is fed even if the core is halted
+// <i> 1: The clock of the involved Timer counter is stopped when the core is halted
+//   <o0.12>   DBG_TIM3_STOP
+// <i> Timer 3 counter stopped when core is halted
+// <i> 0: The clock of the involved Timer Counter is fed even if the core is halted
+// <i> 1: The clock of the involved Timer counter is stopped when the core is halted
+//   <o0.13>   DBG_TIM4_STOP
+// <i> Timer 4 counter stopped when core is halted
+// <i> 0: The clock of the involved Timer Counter is fed even if the core is halted
+// <i> 1: The clock of the involved Timer counter is stopped when the core is halted
+//   <o0.14>   DBG_CAN1_STOP
+// <i> Debug CAN1 stopped when Core is halted
+// <i> 0: Same behavior as in normal mode
+// <i> 1: CAN1 receive registers are frozen
+//   <o0.15>   DBG_I2C1_SMBUS_TIMEOUT
+// <i> I2C1 SMBUS timeout mode stopped when Core is halted
+// <i> 0: Same behavior as in normal mode
+// <i> 1: The SMBUS timeout is frozen
+//   <o0.16>   DBG_I2C2_SMBUS_TIMEOUT
+// <i> I2C2 SMBUS timeout mode stopped when Core is halted
+// <i> 0: Same behavior as in normal mode
+// <i> 1: The SMBUS timeout is frozen
+//   <o0.17>   DBG_TIM8_STOP
+// <i> Timer 8 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.18>   DBG_TIM5_STOP
+// <i> Timer 5 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.19>   DBG_TIM6_STOP
+// <i> Timer 6 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.20>   DBG_TIM7_STOP
+// <i> Timer 7 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.21>   DBG_CAN2_STOP
+// <i> Debug CAN2 stopped when Core is halted
+// <i> 0: Same behavior as in normal mode
+// <i> 1: CAN2 receive registers are frozen
+//   <o0.25>   DBG_TIM12_STOP
+// <i> Timer 12 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.26>   DBG_TIM13_STOP
+// <i> Timer 13 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.27>   DBG_TIM14_STOP
+// <i> Timer 14 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.28>   DBG_TIM9_STOP
+// <i> Timer 9 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.29>   DBG_TIM10_STOP
+// <i> Timer 10 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+//   <o0.30>   DBG_TIM11_STOP
+// <i> Timer 11 counter stopped when core is halted
+// <i> 0: The clock of the involved timer counter is fed even if the core is halted, and the outputs behave normally.
+// <i> 1: The clock of the involved timer counter is stopped when the core is halted, and the outputs are disabled (as if there were an emergency stop in response to a break event).
+// </h>
+DbgMCU_CR = 0x00000007;
+// <<< end of configuration section >>>
\ No newline at end of file

EventRecorderStub.scvd

+<?xml version="1.0" encoding="utf-8"?>
+
+<component_viewer schemaVersion="0.1" xmlns:xs="http://www.w3.org/2001/XMLSchema-instance" xs:noNamespaceSchemaLocation="Component_Viewer.xsd">
+
+<component name="EventRecorderStub" version="1.0.0"/>       <!--name and version of the component-->
+  <events>
+  </events>
+
+</component_viewer>

FreeRTOS/freertos/FreeRTOSConfig.h

+/*
+ * FreeRTOS V202212.01
+ * Copyright (C) 2020 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+#ifndef FREERTOS_CONFIG_H
+#define FREERTOS_CONFIG_H
+
+/*-----------------------------------------------------------
+ * Application specific definitions.
+ *
+ * These definitions should be adjusted for your particular hardware and
+ * application requirements.
+ *
+ * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE
+ * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE.
+ *
+ * See http://www.freertos.org/a00110.html
+ *----------------------------------------------------------*/
+
+#define configUSE_PREEMPTION		1
+#define configUSE_IDLE_HOOK			0
+#define configUSE_TICK_HOOK			0
+#define configCPU_CLOCK_HZ			( ( unsigned long ) 72000000 )
+#define configTICK_RATE_HZ			( ( TickType_t ) 1000 )
+#define configMAX_PRIORITIES		( 5 )
+#define configMINIMAL_STACK_SIZE	( ( unsigned short ) 128 )
+#define configTOTAL_HEAP_SIZE		( ( size_t ) ( 17 * 1024 ) )
+#define configMAX_TASK_NAME_LEN		( 16 )
+#define configUSE_TRACE_FACILITY	0
+#define configUSE_16_BIT_TICKS		0
+#define configIDLE_SHOULD_YIELD		1
+
+
+/* Set the following definitions to 1 to include the API function, or zero
+to exclude the API function. */
+
+#define INCLUDE_vTaskPrioritySet		1
+#define INCLUDE_uxTaskPriorityGet		1
+#define INCLUDE_vTaskDelete				1
+#define INCLUDE_vTaskCleanUpResources	0
+#define INCLUDE_vTaskSuspend			1
+#define INCLUDE_vTaskDelayUntil			1
+#define INCLUDE_vTaskDelay				1
+
+/* This is the raw value as per the Cortex-M3 NVIC.  Values can be 255
+(lowest) to 0 (1?) (highest). */
+#define configKERNEL_INTERRUPT_PRIORITY 		255
+/* !!!! configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to zero !!!!
+See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html. */
+#define configMAX_SYSCALL_INTERRUPT_PRIORITY 	191 /* equivalent to 0xb0, or priority 11. */
+
+
+/* This is the value being used as per the ST library which permits 16
+priority values, 0 to 15.  This must correspond to the
+configKERNEL_INTERRUPT_PRIORITY setting.  Here 15 corresponds to the lowest
+NVIC value of 255. */
+#define configLIBRARY_KERNEL_INTERRUPT_PRIORITY	15
+
+#endif /* FREERTOS_CONFIG_H */
+
+// /**
+//  * 添加三个中断服务函数对的宏定义,FreeRTOS需要用到
+//  */
+#define xPortPendSVHandler PendSV_Handler
+#define vPortSVCHandler SVC_Handler
+#define xPortSysTickHandler SysTick_Handler

FreeRTOS/inc/StackMacros.h

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+
+#ifndef _MSC_VER /* Visual Studio doesn't support #warning. */
+    #warning The name of this file has changed to stack_macros.h.  Please update your code accordingly.  This source file (which has the original name) will be removed in a future release.
+#endif
+
+#include "stack_macros.h"

FreeRTOS/inc/deprecated_definitions.h

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+#ifndef DEPRECATED_DEFINITIONS_H
+#define DEPRECATED_DEFINITIONS_H
+
+
+/* Each FreeRTOS port has a unique portmacro.h header file.  Originally a
+ * pre-processor definition was used to ensure the pre-processor found the correct
+ * portmacro.h file for the port being used.  That scheme was deprecated in favour
+ * of setting the compiler's include path such that it found the correct
+ * portmacro.h file - removing the need for the constant and allowing the
+ * portmacro.h file to be located anywhere in relation to the port being used.  The
+ * definitions below remain in the code for backward compatibility only.  New
+ * projects should not use them. */
+
+#ifdef OPEN_WATCOM_INDUSTRIAL_PC_PORT
+    #include "..\..\Source\portable\owatcom\16bitdos\pc\portmacro.h"
+    typedef void ( __interrupt __far * pxISR )();
+#endif
+
+#ifdef OPEN_WATCOM_FLASH_LITE_186_PORT
+    #include "..\..\Source\portable\owatcom\16bitdos\flsh186\portmacro.h"
+    typedef void ( __interrupt __far * pxISR )();
+#endif
+
+#ifdef GCC_MEGA_AVR
+    #include "../portable/GCC/ATMega323/portmacro.h"
+#endif
+
+#ifdef IAR_MEGA_AVR
+    #include "../portable/IAR/ATMega323/portmacro.h"
+#endif
+
+#ifdef MPLAB_PIC24_PORT
+    #include "../../Source/portable/MPLAB/PIC24_dsPIC/portmacro.h"
+#endif
+
+#ifdef MPLAB_DSPIC_PORT
+    #include "../../Source/portable/MPLAB/PIC24_dsPIC/portmacro.h"
+#endif
+
+#ifdef MPLAB_PIC18F_PORT
+    #include "../../Source/portable/MPLAB/PIC18F/portmacro.h"
+#endif
+
+#ifdef MPLAB_PIC32MX_PORT
+    #include "../../Source/portable/MPLAB/PIC32MX/portmacro.h"
+#endif
+
+#ifdef _FEDPICC
+    #include "libFreeRTOS/Include/portmacro.h"
+#endif
+
+#ifdef SDCC_CYGNAL
+    #include "../../Source/portable/SDCC/Cygnal/portmacro.h"
+#endif
+
+#ifdef GCC_ARM7
+    #include "../../Source/portable/GCC/ARM7_LPC2000/portmacro.h"
+#endif
+
+#ifdef GCC_ARM7_ECLIPSE
+    #include "portmacro.h"
+#endif
+
+#ifdef ROWLEY_LPC23xx
+    #include "../../Source/portable/GCC/ARM7_LPC23xx/portmacro.h"
+#endif
+
+#ifdef IAR_MSP430
+    #include "..\..\Source\portable\IAR\MSP430\portmacro.h"
+#endif
+
+#ifdef GCC_MSP430
+    #include "../../Source/portable/GCC/MSP430F449/portmacro.h"
+#endif
+
+#ifdef ROWLEY_MSP430
+    #include "../../Source/portable/Rowley/MSP430F449/portmacro.h"
+#endif
+
+#ifdef ARM7_LPC21xx_KEIL_RVDS
+    #include "..\..\Source\portable\RVDS\ARM7_LPC21xx\portmacro.h"
+#endif
+
+#ifdef SAM7_GCC
+    #include "../../Source/portable/GCC/ARM7_AT91SAM7S/portmacro.h"
+#endif
+
+#ifdef SAM7_IAR
+    #include "..\..\Source\portable\IAR\AtmelSAM7S64\portmacro.h"
+#endif
+
+#ifdef SAM9XE_IAR
+    #include "..\..\Source\portable\IAR\AtmelSAM9XE\portmacro.h"
+#endif
+
+#ifdef LPC2000_IAR
+    #include "..\..\Source\portable\IAR\LPC2000\portmacro.h"
+#endif
+
+#ifdef STR71X_IAR
+    #include "..\..\Source\portable\IAR\STR71x\portmacro.h"
+#endif
+
+#ifdef STR75X_IAR
+    #include "..\..\Source\portable\IAR\STR75x\portmacro.h"
+#endif
+
+#ifdef STR75X_GCC
+    #include "..\..\Source\portable\GCC\STR75x\portmacro.h"
+#endif
+
+#ifdef STR91X_IAR
+    #include "..\..\Source\portable\IAR\STR91x\portmacro.h"
+#endif
+
+#ifdef GCC_H8S
+    #include "../../Source/portable/GCC/H8S2329/portmacro.h"
+#endif
+
+#ifdef GCC_AT91FR40008
+    #include "../../Source/portable/GCC/ARM7_AT91FR40008/portmacro.h"
+#endif
+
+#ifdef RVDS_ARMCM3_LM3S102
+    #include "../../Source/portable/RVDS/ARM_CM3/portmacro.h"
+#endif
+
+#ifdef GCC_ARMCM3_LM3S102
+    #include "../../Source/portable/GCC/ARM_CM3/portmacro.h"
+#endif
+
+#ifdef GCC_ARMCM3
+    #include "../../Source/portable/GCC/ARM_CM3/portmacro.h"
+#endif
+
+#ifdef IAR_ARM_CM3
+    #include "../../Source/portable/IAR/ARM_CM3/portmacro.h"
+#endif
+
+#ifdef IAR_ARMCM3_LM
+    #include "../../Source/portable/IAR/ARM_CM3/portmacro.h"
+#endif
+
+#ifdef HCS12_CODE_WARRIOR
+    #include "../../Source/portable/CodeWarrior/HCS12/portmacro.h"
+#endif
+
+#ifdef MICROBLAZE_GCC
+    #include "../../Source/portable/GCC/MicroBlaze/portmacro.h"
+#endif
+
+#ifdef TERN_EE
+    #include "..\..\Source\portable\Paradigm\Tern_EE\small\portmacro.h"
+#endif
+
+#ifdef GCC_HCS12
+    #include "../../Source/portable/GCC/HCS12/portmacro.h"
+#endif
+
+#ifdef GCC_MCF5235
+    #include "../../Source/portable/GCC/MCF5235/portmacro.h"
+#endif
+
+#ifdef COLDFIRE_V2_GCC
+    #include "../../../Source/portable/GCC/ColdFire_V2/portmacro.h"
+#endif
+
+#ifdef COLDFIRE_V2_CODEWARRIOR
+    #include "../../Source/portable/CodeWarrior/ColdFire_V2/portmacro.h"
+#endif
+
+#ifdef GCC_PPC405
+    #include "../../Source/portable/GCC/PPC405_Xilinx/portmacro.h"
+#endif
+
+#ifdef GCC_PPC440
+    #include "../../Source/portable/GCC/PPC440_Xilinx/portmacro.h"
+#endif
+
+#ifdef _16FX_SOFTUNE
+    #include "..\..\Source\portable\Softune\MB96340\portmacro.h"
+#endif
+
+#ifdef BCC_INDUSTRIAL_PC_PORT
+
+/* A short file name has to be used in place of the normal
+ * FreeRTOSConfig.h when using the Borland compiler. */
+    #include "frconfig.h"
+    #include "..\portable\BCC\16BitDOS\PC\prtmacro.h"
+    typedef void ( __interrupt __far * pxISR )();
+#endif
+
+#ifdef BCC_FLASH_LITE_186_PORT
+
+/* A short file name has to be used in place of the normal
+ * FreeRTOSConfig.h when using the Borland compiler. */
+    #include "frconfig.h"
+    #include "..\portable\BCC\16BitDOS\flsh186\prtmacro.h"
+    typedef void ( __interrupt __far * pxISR )();
+#endif
+
+#ifdef __GNUC__
+    #ifdef __AVR32_AVR32A__
+        #include "portmacro.h"
+    #endif
+#endif
+
+#ifdef __ICCAVR32__
+    #ifdef __CORE__
+        #if __CORE__ == __AVR32A__
+            #include "portmacro.h"
+        #endif
+    #endif
+#endif
+
+#ifdef __91467D
+    #include "portmacro.h"
+#endif
+
+#ifdef __96340
+    #include "portmacro.h"
+#endif
+
+
+#ifdef __IAR_V850ES_Fx3__
+    #include "../../Source/portable/IAR/V850ES/portmacro.h"
+#endif
+
+#ifdef __IAR_V850ES_Jx3__
+    #include "../../Source/portable/IAR/V850ES/portmacro.h"
+#endif
+
+#ifdef __IAR_V850ES_Jx3_L__
+    #include "../../Source/portable/IAR/V850ES/portmacro.h"
+#endif
+
+#ifdef __IAR_V850ES_Jx2__
+    #include "../../Source/portable/IAR/V850ES/portmacro.h"
+#endif
+
+#ifdef __IAR_V850ES_Hx2__
+    #include "../../Source/portable/IAR/V850ES/portmacro.h"
+#endif
+
+#ifdef __IAR_78K0R_Kx3__
+    #include "../../Source/portable/IAR/78K0R/portmacro.h"
+#endif
+
+#ifdef __IAR_78K0R_Kx3L__
+    #include "../../Source/portable/IAR/78K0R/portmacro.h"
+#endif
+
+#endif /* DEPRECATED_DEFINITIONS_H */

FreeRTOS/inc/portable.h

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+/*-----------------------------------------------------------
+* Portable layer API.  Each function must be defined for each port.
+*----------------------------------------------------------*/
+
+#ifndef PORTABLE_H
+#define PORTABLE_H
+
+/* Each FreeRTOS port has a unique portmacro.h header file.  Originally a
+ * pre-processor definition was used to ensure the pre-processor found the correct
+ * portmacro.h file for the port being used.  That scheme was deprecated in favour
+ * of setting the compiler's include path such that it found the correct
+ * portmacro.h file - removing the need for the constant and allowing the
+ * portmacro.h file to be located anywhere in relation to the port being used.
+ * Purely for reasons of backward compatibility the old method is still valid, but
+ * to make it clear that new projects should not use it, support for the port
+ * specific constants has been moved into the deprecated_definitions.h header
+ * file. */
+#include "deprecated_definitions.h"
+
+/* If portENTER_CRITICAL is not defined then including deprecated_definitions.h
+ * did not result in a portmacro.h header file being included - and it should be
+ * included here.  In this case the path to the correct portmacro.h header file
+ * must be set in the compiler's include path. */
+#ifndef portENTER_CRITICAL
+    #include "portmacro.h"
+#endif
+
+#if portBYTE_ALIGNMENT == 32
+    #define portBYTE_ALIGNMENT_MASK    ( 0x001f )
+#elif portBYTE_ALIGNMENT == 16
+    #define portBYTE_ALIGNMENT_MASK    ( 0x000f )
+#elif portBYTE_ALIGNMENT == 8
+    #define portBYTE_ALIGNMENT_MASK    ( 0x0007 )
+#elif portBYTE_ALIGNMENT == 4
+    #define portBYTE_ALIGNMENT_MASK    ( 0x0003 )
+#elif portBYTE_ALIGNMENT == 2
+    #define portBYTE_ALIGNMENT_MASK    ( 0x0001 )
+#elif portBYTE_ALIGNMENT == 1
+    #define portBYTE_ALIGNMENT_MASK    ( 0x0000 )
+#else /* if portBYTE_ALIGNMENT == 32 */
+    #error "Invalid portBYTE_ALIGNMENT definition"
+#endif /* if portBYTE_ALIGNMENT == 32 */
+
+#ifndef portUSING_MPU_WRAPPERS
+    #define portUSING_MPU_WRAPPERS    0
+#endif
+
+#ifndef portNUM_CONFIGURABLE_REGIONS
+    #define portNUM_CONFIGURABLE_REGIONS    1
+#endif
+
+#ifndef portHAS_STACK_OVERFLOW_CHECKING
+    #define portHAS_STACK_OVERFLOW_CHECKING    0
+#endif
+
+#ifndef portARCH_NAME
+    #define portARCH_NAME    NULL
+#endif
+
+#ifndef configSTACK_ALLOCATION_FROM_SEPARATE_HEAP
+    /* Defaults to 0 for backward compatibility. */
+    #define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP    0
+#endif
+
+/* *INDENT-OFF* */
+#ifdef __cplusplus
+    extern "C" {
+#endif
+/* *INDENT-ON* */
+
+#include "mpu_wrappers.h"
+
+/*
+ * Setup the stack of a new task so it is ready to be placed under the
+ * scheduler control.  The registers have to be placed on the stack in
+ * the order that the port expects to find them.
+ *
+ */
+#if ( portUSING_MPU_WRAPPERS == 1 )
+    #if ( portHAS_STACK_OVERFLOW_CHECKING == 1 )
+        StackType_t * pxPortInitialiseStack( StackType_t * pxTopOfStack,
+                                             StackType_t * pxEndOfStack,
+                                             TaskFunction_t pxCode,
+                                             void * pvParameters,
+                                             BaseType_t xRunPrivileged ) PRIVILEGED_FUNCTION;
+    #else
+        StackType_t * pxPortInitialiseStack( StackType_t * pxTopOfStack,
+                                             TaskFunction_t pxCode,
+                                             void * pvParameters,
+                                             BaseType_t xRunPrivileged ) PRIVILEGED_FUNCTION;
+    #endif
+#else /* if ( portUSING_MPU_WRAPPERS == 1 ) */
+    #if ( portHAS_STACK_OVERFLOW_CHECKING == 1 )
+        StackType_t * pxPortInitialiseStack( StackType_t * pxTopOfStack,
+                                             StackType_t * pxEndOfStack,
+                                             TaskFunction_t pxCode,
+                                             void * pvParameters ) PRIVILEGED_FUNCTION;
+    #else
+        StackType_t * pxPortInitialiseStack( StackType_t * pxTopOfStack,
+                                             TaskFunction_t pxCode,
+                                             void * pvParameters ) PRIVILEGED_FUNCTION;
+    #endif
+#endif /* if ( portUSING_MPU_WRAPPERS == 1 ) */
+
+/* Used by heap_5.c to define the start address and size of each memory region
+ * that together comprise the total FreeRTOS heap space. */
+typedef struct HeapRegion
+{
+    uint8_t * pucStartAddress;
+    size_t xSizeInBytes;
+} HeapRegion_t;
+
+/* Used to pass information about the heap out of vPortGetHeapStats(). */
+typedef struct xHeapStats
+{
+    size_t xAvailableHeapSpaceInBytes;      /* The total heap size currently available - this is the sum of all the free blocks, not the largest block that can be allocated. */
+    size_t xSizeOfLargestFreeBlockInBytes;  /* The maximum size, in bytes, of all the free blocks within the heap at the time vPortGetHeapStats() is called. */
+    size_t xSizeOfSmallestFreeBlockInBytes; /* The minimum size, in bytes, of all the free blocks within the heap at the time vPortGetHeapStats() is called. */
+    size_t xNumberOfFreeBlocks;             /* The number of free memory blocks within the heap at the time vPortGetHeapStats() is called. */
+    size_t xMinimumEverFreeBytesRemaining;  /* The minimum amount of total free memory (sum of all free blocks) there has been in the heap since the system booted. */
+    size_t xNumberOfSuccessfulAllocations;  /* The number of calls to pvPortMalloc() that have returned a valid memory block. */
+    size_t xNumberOfSuccessfulFrees;        /* The number of calls to vPortFree() that has successfully freed a block of memory. */
+} HeapStats_t;
+
+/*
+ * Used to define multiple heap regions for use by heap_5.c.  This function
+ * must be called before any calls to pvPortMalloc() - not creating a task,
+ * queue, semaphore, mutex, software timer, event group, etc. will result in
+ * pvPortMalloc being called.
+ *
+ * pxHeapRegions passes in an array of HeapRegion_t structures - each of which
+ * defines a region of memory that can be used as the heap.  The array is
+ * terminated by a HeapRegions_t structure that has a size of 0.  The region
+ * with the lowest start address must appear first in the array.
+ */
+void vPortDefineHeapRegions( const HeapRegion_t * const pxHeapRegions ) PRIVILEGED_FUNCTION;
+
+/*
+ * Returns a HeapStats_t structure filled with information about the current
+ * heap state.
+ */
+void vPortGetHeapStats( HeapStats_t * pxHeapStats );
+
+/*
+ * Map to the memory management routines required for the port.
+ */
+void * pvPortMalloc( size_t xSize ) PRIVILEGED_FUNCTION;
+void * pvPortCalloc( size_t xNum,
+                     size_t xSize ) PRIVILEGED_FUNCTION;
+void vPortFree( void * pv ) PRIVILEGED_FUNCTION;
+void vPortInitialiseBlocks( void ) PRIVILEGED_FUNCTION;
+size_t xPortGetFreeHeapSize( void ) PRIVILEGED_FUNCTION;
+size_t xPortGetMinimumEverFreeHeapSize( void ) PRIVILEGED_FUNCTION;
+
+#if ( configSTACK_ALLOCATION_FROM_SEPARATE_HEAP == 1 )
+    void * pvPortMallocStack( size_t xSize ) PRIVILEGED_FUNCTION;
+    void vPortFreeStack( void * pv ) PRIVILEGED_FUNCTION;
+#else
+    #define pvPortMallocStack    pvPortMalloc
+    #define vPortFreeStack       vPortFree
+#endif
+
+#if ( configUSE_MALLOC_FAILED_HOOK == 1 )
+
+/**
+ * task.h
+ * @code{c}
+ * void vApplicationMallocFailedHook( void )
+ * @endcode
+ *
+ * This hook function is called when allocation failed.
+ */
+    void vApplicationMallocFailedHook( void ); /*lint !e526 Symbol not defined as it is an application callback. */
+#endif
+
+/*
+ * Setup the hardware ready for the scheduler to take control.  This generally
+ * sets up a tick interrupt and sets timers for the correct tick frequency.
+ */
+BaseType_t xPortStartScheduler( void ) PRIVILEGED_FUNCTION;
+
+/*
+ * Undo any hardware/ISR setup that was performed by xPortStartScheduler() so
+ * the hardware is left in its original condition after the scheduler stops
+ * executing.
+ */
+void vPortEndScheduler( void ) PRIVILEGED_FUNCTION;
+
+/*
+ * The structures and methods of manipulating the MPU are contained within the
+ * port layer.
+ *
+ * Fills the xMPUSettings structure with the memory region information
+ * contained in xRegions.
+ */
+#if ( portUSING_MPU_WRAPPERS == 1 )
+    struct xMEMORY_REGION;
+    void vPortStoreTaskMPUSettings( xMPU_SETTINGS * xMPUSettings,
+                                    const struct xMEMORY_REGION * const xRegions,
+                                    StackType_t * pxBottomOfStack,
+                                    uint32_t ulStackDepth ) PRIVILEGED_FUNCTION;
+#endif
+
+/* *INDENT-OFF* */
+#ifdef __cplusplus
+    }
+#endif
+/* *INDENT-ON* */
+
+#endif /* PORTABLE_H */

FreeRTOS/inc/projdefs.h

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+#ifndef PROJDEFS_H
+#define PROJDEFS_H
+
+/*
+ * Defines the prototype to which task functions must conform.  Defined in this
+ * file to ensure the type is known before portable.h is included.
+ */
+typedef void (* TaskFunction_t)( void * );
+
+/* Converts a time in milliseconds to a time in ticks.  This macro can be
+ * overridden by a macro of the same name defined in FreeRTOSConfig.h in case the
+ * definition here is not suitable for your application. */
+#ifndef pdMS_TO_TICKS
+    #define pdMS_TO_TICKS( xTimeInMs )    ( ( TickType_t ) ( ( ( TickType_t ) ( xTimeInMs ) * ( TickType_t ) configTICK_RATE_HZ ) / ( TickType_t ) 1000U ) )
+#endif
+
+#define pdFALSE                                  ( ( BaseType_t ) 0 )
+#define pdTRUE                                   ( ( BaseType_t ) 1 )
+
+#define pdPASS                                   ( pdTRUE )
+#define pdFAIL                                   ( pdFALSE )
+#define errQUEUE_EMPTY                           ( ( BaseType_t ) 0 )
+#define errQUEUE_FULL                            ( ( BaseType_t ) 0 )
+
+/* FreeRTOS error definitions. */
+#define errCOULD_NOT_ALLOCATE_REQUIRED_MEMORY    ( -1 )
+#define errQUEUE_BLOCKED                         ( -4 )
+#define errQUEUE_YIELD                           ( -5 )
+
+/* Macros used for basic data corruption checks. */
+#ifndef configUSE_LIST_DATA_INTEGRITY_CHECK_BYTES
+    #define configUSE_LIST_DATA_INTEGRITY_CHECK_BYTES    0
+#endif
+
+#if ( configUSE_16_BIT_TICKS == 1 )
+    #define pdINTEGRITY_CHECK_VALUE    0x5a5a
+#else
+    #define pdINTEGRITY_CHECK_VALUE    0x5a5a5a5aUL
+#endif
+
+/* The following errno values are used by FreeRTOS+ components, not FreeRTOS
+ * itself. */
+#define pdFREERTOS_ERRNO_NONE             0   /* No errors */
+#define pdFREERTOS_ERRNO_ENOENT           2   /* No such file or directory */
+#define pdFREERTOS_ERRNO_EINTR            4   /* Interrupted system call */
+#define pdFREERTOS_ERRNO_EIO              5   /* I/O error */
+#define pdFREERTOS_ERRNO_ENXIO            6   /* No such device or address */
+#define pdFREERTOS_ERRNO_EBADF            9   /* Bad file number */
+#define pdFREERTOS_ERRNO_EAGAIN           11  /* No more processes */
+#define pdFREERTOS_ERRNO_EWOULDBLOCK      11  /* Operation would block */
+#define pdFREERTOS_ERRNO_ENOMEM           12  /* Not enough memory */
+#define pdFREERTOS_ERRNO_EACCES           13  /* Permission denied */
+#define pdFREERTOS_ERRNO_EFAULT           14  /* Bad address */
+#define pdFREERTOS_ERRNO_EBUSY            16  /* Mount device busy */
+#define pdFREERTOS_ERRNO_EEXIST           17  /* File exists */
+#define pdFREERTOS_ERRNO_EXDEV            18  /* Cross-device link */
+#define pdFREERTOS_ERRNO_ENODEV           19  /* No such device */
+#define pdFREERTOS_ERRNO_ENOTDIR          20  /* Not a directory */
+#define pdFREERTOS_ERRNO_EISDIR           21  /* Is a directory */
+#define pdFREERTOS_ERRNO_EINVAL           22  /* Invalid argument */
+#define pdFREERTOS_ERRNO_ENOSPC           28  /* No space left on device */
+#define pdFREERTOS_ERRNO_ESPIPE           29  /* Illegal seek */
+#define pdFREERTOS_ERRNO_EROFS            30  /* Read only file system */
+#define pdFREERTOS_ERRNO_EUNATCH          42  /* Protocol driver not attached */
+#define pdFREERTOS_ERRNO_EBADE            50  /* Invalid exchange */
+#define pdFREERTOS_ERRNO_EFTYPE           79  /* Inappropriate file type or format */
+#define pdFREERTOS_ERRNO_ENMFILE          89  /* No more files */
+#define pdFREERTOS_ERRNO_ENOTEMPTY        90  /* Directory not empty */
+#define pdFREERTOS_ERRNO_ENAMETOOLONG     91  /* File or path name too long */
+#define pdFREERTOS_ERRNO_EOPNOTSUPP       95  /* Operation not supported on transport endpoint */
+#define pdFREERTOS_ERRNO_ENOBUFS          105 /* No buffer space available */
+#define pdFREERTOS_ERRNO_ENOPROTOOPT      109 /* Protocol not available */
+#define pdFREERTOS_ERRNO_EADDRINUSE       112 /* Address already in use */
+#define pdFREERTOS_ERRNO_ETIMEDOUT        116 /* Connection timed out */
+#define pdFREERTOS_ERRNO_EINPROGRESS      119 /* Connection already in progress */
+#define pdFREERTOS_ERRNO_EALREADY         120 /* Socket already connected */
+#define pdFREERTOS_ERRNO_EADDRNOTAVAIL    125 /* Address not available */
+#define pdFREERTOS_ERRNO_EISCONN          127 /* Socket is already connected */
+#define pdFREERTOS_ERRNO_ENOTCONN         128 /* Socket is not connected */
+#define pdFREERTOS_ERRNO_ENOMEDIUM        135 /* No medium inserted */
+#define pdFREERTOS_ERRNO_EILSEQ           138 /* An invalid UTF-16 sequence was encountered. */
+#define pdFREERTOS_ERRNO_ECANCELED        140 /* Operation canceled. */
+
+/* The following endian values are used by FreeRTOS+ components, not FreeRTOS
+ * itself. */
+#define pdFREERTOS_LITTLE_ENDIAN          0
+#define pdFREERTOS_BIG_ENDIAN             1
+
+/* Re-defining endian values for generic naming. */
+#define pdLITTLE_ENDIAN                   pdFREERTOS_LITTLE_ENDIAN
+#define pdBIG_ENDIAN                      pdFREERTOS_BIG_ENDIAN
+
+
+#endif /* PROJDEFS_H */

FreeRTOS/inc/stack_macros.h

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+#ifndef STACK_MACROS_H
+#define STACK_MACROS_H
+
+/*
+ * Call the stack overflow hook function if the stack of the task being swapped
+ * out is currently overflowed, or looks like it might have overflowed in the
+ * past.
+ *
+ * Setting configCHECK_FOR_STACK_OVERFLOW to 1 will cause the macro to check
+ * the current stack state only - comparing the current top of stack value to
+ * the stack limit.  Setting configCHECK_FOR_STACK_OVERFLOW to greater than 1
+ * will also cause the last few stack bytes to be checked to ensure the value
+ * to which the bytes were set when the task was created have not been
+ * overwritten.  Note this second test does not guarantee that an overflowed
+ * stack will always be recognised.
+ */
+
+/*-----------------------------------------------------------*/
+
+/*
+ * portSTACK_LIMIT_PADDING is a number of extra words to consider to be in
+ * use on the stack.
+ */
+#ifndef portSTACK_LIMIT_PADDING
+    #define portSTACK_LIMIT_PADDING    0
+#endif
+
+#if ( ( configCHECK_FOR_STACK_OVERFLOW == 1 ) && ( portSTACK_GROWTH < 0 ) )
+
+/* Only the current stack state is to be checked. */
+    #define taskCHECK_FOR_STACK_OVERFLOW()                                                            \
+    {                                                                                                 \
+        /* Is the currently saved stack pointer within the stack limit? */                            \
+        if( pxCurrentTCB->pxTopOfStack <= pxCurrentTCB->pxStack + portSTACK_LIMIT_PADDING )           \
+        {                                                                                             \
+            vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName ); \
+        }                                                                                             \
+    }
+
+#endif /* configCHECK_FOR_STACK_OVERFLOW == 1 */
+/*-----------------------------------------------------------*/
+
+#if ( ( configCHECK_FOR_STACK_OVERFLOW == 1 ) && ( portSTACK_GROWTH > 0 ) )
+
+/* Only the current stack state is to be checked. */
+    #define taskCHECK_FOR_STACK_OVERFLOW()                                                            \
+    {                                                                                                 \
+                                                                                                      \
+        /* Is the currently saved stack pointer within the stack limit? */                            \
+        if( pxCurrentTCB->pxTopOfStack >= pxCurrentTCB->pxEndOfStack - portSTACK_LIMIT_PADDING )      \
+        {                                                                                             \
+            vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName ); \
+        }                                                                                             \
+    }
+
+#endif /* configCHECK_FOR_STACK_OVERFLOW == 1 */
+/*-----------------------------------------------------------*/
+
+#if ( ( configCHECK_FOR_STACK_OVERFLOW > 1 ) && ( portSTACK_GROWTH < 0 ) )
+
+    #define taskCHECK_FOR_STACK_OVERFLOW()                                                            \
+    {                                                                                                 \
+        const uint32_t * const pulStack = ( uint32_t * ) pxCurrentTCB->pxStack;                       \
+        const uint32_t ulCheckValue = ( uint32_t ) 0xa5a5a5a5;                                        \
+                                                                                                      \
+        if( ( pulStack[ 0 ] != ulCheckValue ) ||                                                      \
+            ( pulStack[ 1 ] != ulCheckValue ) ||                                                      \
+            ( pulStack[ 2 ] != ulCheckValue ) ||                                                      \
+            ( pulStack[ 3 ] != ulCheckValue ) )                                                       \
+        {                                                                                             \
+            vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName ); \
+        }                                                                                             \
+    }
+
+#endif /* #if( configCHECK_FOR_STACK_OVERFLOW > 1 ) */
+/*-----------------------------------------------------------*/
+
+#if ( ( configCHECK_FOR_STACK_OVERFLOW > 1 ) && ( portSTACK_GROWTH > 0 ) )
+
+    #define taskCHECK_FOR_STACK_OVERFLOW()                                                                                                \
+    {                                                                                                                                     \
+        int8_t * pcEndOfStack = ( int8_t * ) pxCurrentTCB->pxEndOfStack;                                                                  \
+        static const uint8_t ucExpectedStackBytes[] = { tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE,   \
+                                                        tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE,   \
+                                                        tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE,   \
+                                                        tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE,   \
+                                                        tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE, tskSTACK_FILL_BYTE }; \
+                                                                                                                                          \
+                                                                                                                                          \
+        pcEndOfStack -= sizeof( ucExpectedStackBytes );                                                                                   \
+                                                                                                                                          \
+        /* Has the extremity of the task stack ever been written over? */                                                                 \
+        if( memcmp( ( void * ) pcEndOfStack, ( void * ) ucExpectedStackBytes, sizeof( ucExpectedStackBytes ) ) != 0 )                     \
+        {                                                                                                                                 \
+            vApplicationStackOverflowHook( ( TaskHandle_t ) pxCurrentTCB, pxCurrentTCB->pcTaskName );                                     \
+        }                                                                                                                                 \
+    }
+
+#endif /* #if( configCHECK_FOR_STACK_OVERFLOW > 1 ) */
+/*-----------------------------------------------------------*/
+
+/* Remove stack overflow macro if not being used. */
+#ifndef taskCHECK_FOR_STACK_OVERFLOW
+    #define taskCHECK_FOR_STACK_OVERFLOW()
+#endif
+
+
+
+#endif /* STACK_MACROS_H */

FreeRTOS/inc/stdint.readme

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+#ifndef FREERTOS_STDINT
+#define FREERTOS_STDINT
+
+/*******************************************************************************
+ * THIS IS NOT A FULL stdint.h IMPLEMENTATION - It only contains the definitions
+ * necessary to build the FreeRTOS code.  It is provided to allow FreeRTOS to be
+ * built using compilers that do not provide their own stdint.h definition.
+ *
+ * To use this file:
+ *
+ *    1) Copy this file into the directory that contains your FreeRTOSConfig.h
+ *       header file, as that directory will already be in the compiler's include
+ *       path.
+ *
+ *    2) Rename the copied file stdint.h.
+ *
+ */
+
+typedef signed char int8_t;
+typedef unsigned char uint8_t;
+typedef short int16_t;
+typedef unsigned short uint16_t;
+typedef long int32_t;
+typedef unsigned long uint32_t;
+
+#ifndef SIZE_MAX
+    #define SIZE_MAX    ( ( size_t ) -1 )
+#endif
+
+#endif /* FREERTOS_STDINT */

FreeRTOS/prot/heap_1.c

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+
+/*
+ * The simplest possible implementation of pvPortMalloc().  Note that this
+ * implementation does NOT allow allocated memory to be freed again.
+ *
+ * See heap_2.c, heap_3.c and heap_4.c for alternative implementations, and the
+ * memory management pages of https://www.FreeRTOS.org for more information.
+ */
+#include <stdlib.h>
+
+/* Defining MPU_WRAPPERS_INCLUDED_FROM_API_FILE prevents task.h from redefining
+ * all the API functions to use the MPU wrappers.  That should only be done when
+ * task.h is included from an application file. */
+#define MPU_WRAPPERS_INCLUDED_FROM_API_FILE
+
+#include "FreeRTOS.h"
+#include "task.h"
+
+#undef MPU_WRAPPERS_INCLUDED_FROM_API_FILE
+
+#if ( configSUPPORT_DYNAMIC_ALLOCATION == 0 )
+    #error This file must not be used if configSUPPORT_DYNAMIC_ALLOCATION is 0
+#endif
+
+/* A few bytes might be lost to byte aligning the heap start address. */
+#define configADJUSTED_HEAP_SIZE    ( configTOTAL_HEAP_SIZE - portBYTE_ALIGNMENT )
+
+/* Allocate the memory for the heap. */
+#if ( configAPPLICATION_ALLOCATED_HEAP == 1 )
+
+/* The application writer has already defined the array used for the RTOS
+* heap - probably so it can be placed in a special segment or address. */
+    extern uint8_t ucHeap[ configTOTAL_HEAP_SIZE ];
+#else
+    static uint8_t ucHeap[ configTOTAL_HEAP_SIZE ];
+#endif /* configAPPLICATION_ALLOCATED_HEAP */
+
+/* Index into the ucHeap array. */
+static size_t xNextFreeByte = ( size_t ) 0;
+
+/*-----------------------------------------------------------*/
+
+void * pvPortMalloc( size_t xWantedSize )
+{
+    void * pvReturn = NULL;
+    static uint8_t * pucAlignedHeap = NULL;
+
+    /* Ensure that blocks are always aligned. */
+    #if ( portBYTE_ALIGNMENT != 1 )
+    {
+        if( xWantedSize & portBYTE_ALIGNMENT_MASK )
+        {
+            /* Byte alignment required. Check for overflow. */
+            if( ( xWantedSize + ( portBYTE_ALIGNMENT - ( xWantedSize & portBYTE_ALIGNMENT_MASK ) ) ) > xWantedSize )
+            {
+                xWantedSize += ( portBYTE_ALIGNMENT - ( xWantedSize & portBYTE_ALIGNMENT_MASK ) );
+            }
+            else
+            {
+                xWantedSize = 0;
+            }
+        }
+    }
+    #endif /* if ( portBYTE_ALIGNMENT != 1 ) */
+
+    vTaskSuspendAll();
+    {
+        if( pucAlignedHeap == NULL )
+        {
+            /* Ensure the heap starts on a correctly aligned boundary. */
+            pucAlignedHeap = ( uint8_t * ) ( ( ( portPOINTER_SIZE_TYPE ) & ucHeap[ portBYTE_ALIGNMENT - 1 ] ) & ( ~( ( portPOINTER_SIZE_TYPE ) portBYTE_ALIGNMENT_MASK ) ) );
+        }
+
+        /* Check there is enough room left for the allocation and. */
+        if( ( xWantedSize > 0 ) &&                                /* valid size */
+            ( ( xNextFreeByte + xWantedSize ) < configADJUSTED_HEAP_SIZE ) &&
+            ( ( xNextFreeByte + xWantedSize ) > xNextFreeByte ) ) /* Check for overflow. */
+        {
+            /* Return the next free byte then increment the index past this
+             * block. */
+            pvReturn = pucAlignedHeap + xNextFreeByte;
+            xNextFreeByte += xWantedSize;
+        }
+
+        traceMALLOC( pvReturn, xWantedSize );
+    }
+    ( void ) xTaskResumeAll();
+
+    #if ( configUSE_MALLOC_FAILED_HOOK == 1 )
+    {
+        if( pvReturn == NULL )
+        {
+            vApplicationMallocFailedHook();
+        }
+    }
+    #endif
+
+    return pvReturn;
+}
+/*-----------------------------------------------------------*/
+
+void vPortFree( void * pv )
+{
+    /* Memory cannot be freed using this scheme.  See heap_2.c, heap_3.c and
+     * heap_4.c for alternative implementations, and the memory management pages of
+     * https://www.FreeRTOS.org for more information. */
+    ( void ) pv;
+
+    /* Force an assert as it is invalid to call this function. */
+    configASSERT( pv == NULL );
+}
+/*-----------------------------------------------------------*/
+
+void vPortInitialiseBlocks( void )
+{
+    /* Only required when static memory is not cleared. */
+    xNextFreeByte = ( size_t ) 0;
+}
+/*-----------------------------------------------------------*/
+
+size_t xPortGetFreeHeapSize( void )
+{
+    return( configADJUSTED_HEAP_SIZE - xNextFreeByte );
+}

FreeRTOS/prot/heap_3.c

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+
+/*
+ * Implementation of pvPortMalloc() and vPortFree() that relies on the
+ * compilers own malloc() and free() implementations.
+ *
+ * This file can only be used if the linker is configured to to generate
+ * a heap memory area.
+ *
+ * See heap_1.c, heap_2.c and heap_4.c for alternative implementations, and the
+ * memory management pages of https://www.FreeRTOS.org for more information.
+ */
+
+#include <stdlib.h>
+
+/* Defining MPU_WRAPPERS_INCLUDED_FROM_API_FILE prevents task.h from redefining
+ * all the API functions to use the MPU wrappers.  That should only be done when
+ * task.h is included from an application file. */
+#define MPU_WRAPPERS_INCLUDED_FROM_API_FILE
+
+#include "FreeRTOS.h"
+#include "task.h"
+
+#undef MPU_WRAPPERS_INCLUDED_FROM_API_FILE
+
+#if ( configSUPPORT_DYNAMIC_ALLOCATION == 0 )
+    #error This file must not be used if configSUPPORT_DYNAMIC_ALLOCATION is 0
+#endif
+
+/*-----------------------------------------------------------*/
+
+void * pvPortMalloc( size_t xWantedSize )
+{
+    void * pvReturn;
+
+    vTaskSuspendAll();
+    {
+        pvReturn = malloc( xWantedSize );
+        traceMALLOC( pvReturn, xWantedSize );
+    }
+    ( void ) xTaskResumeAll();
+
+    #if ( configUSE_MALLOC_FAILED_HOOK == 1 )
+    {
+        if( pvReturn == NULL )
+        {
+            vApplicationMallocFailedHook();
+        }
+    }
+    #endif
+
+    return pvReturn;
+}
+/*-----------------------------------------------------------*/
+
+void vPortFree( void * pv )
+{
+    if( pv != NULL )
+    {
+        vTaskSuspendAll();
+        {
+            free( pv );
+            traceFREE( pv, 0 );
+        }
+        ( void ) xTaskResumeAll();
+    }
+}

FreeRTOS/prot/portmacro.h

+/*
+ * FreeRTOS Kernel V10.5.1
+ * Copyright (C) 2021 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * SPDX-License-Identifier: MIT
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * https://www.FreeRTOS.org
+ * https://github.com/FreeRTOS
+ *
+ */
+
+
+#ifndef PORTMACRO_H
+#define PORTMACRO_H
+
+/* *INDENT-OFF* */
+#ifdef __cplusplus
+    extern "C" {
+#endif
+/* *INDENT-ON* */
+
+/*-----------------------------------------------------------
+ * Port specific definitions.
+ *
+ * The settings in this file configure FreeRTOS correctly for the
+ * given hardware and compiler.
+ *
+ * These settings should not be altered.
+ *-----------------------------------------------------------
+ */
+
+/* Type definitions. */
+    #define portCHAR          char
+    #define portFLOAT         float
+    #define portDOUBLE        double
+    #define portLONG          long
+    #define portSHORT         short
+    #define portSTACK_TYPE    uint32_t
+    #define portBASE_TYPE     long
+
+    typedef portSTACK_TYPE   StackType_t;
+    typedef long             BaseType_t;
+    typedef unsigned long    UBaseType_t;
+
+    #if ( configUSE_16_BIT_TICKS == 1 )
+        typedef uint16_t     TickType_t;
+        #define portMAX_DELAY              ( TickType_t ) 0xffff
+    #else
+        typedef uint32_t     TickType_t;
+        #define portMAX_DELAY              ( TickType_t ) 0xffffffffUL
+
+/* 32-bit tick type on a 32-bit architecture, so reads of the tick count do
+ * not need to be guarded with a critical section. */
+        #define portTICK_TYPE_IS_ATOMIC    1
+    #endif
+/*-----------------------------------------------------------*/
+
+/* Architecture specifics. */
+    #define portSTACK_GROWTH          ( -1 )
+    #define portTICK_PERIOD_MS        ( ( TickType_t ) 1000 / configTICK_RATE_HZ )
+    #define portBYTE_ALIGNMENT        8
+
+/* Constants used with memory barrier intrinsics. */
+    #define portSY_FULL_READ_WRITE    ( 15 )
+
+/*-----------------------------------------------------------*/
+
+/* Scheduler utilities. */
+    #define portYIELD()                                 \
+    {                                                   \
+        /* Set a PendSV to request a context switch. */ \
+        portNVIC_INT_CTRL_REG = portNVIC_PENDSVSET_BIT; \
+                                                        \
+        /* Barriers are normally not required but do ensure the code is completely \
+         * within the specified behaviour for the architecture. */ \
+        __dsb( portSY_FULL_READ_WRITE );                           \
+        __isb( portSY_FULL_READ_WRITE );                           \
+    }
+/*-----------------------------------------------------------*/
+
+    #define portNVIC_INT_CTRL_REG     ( *( ( volatile uint32_t * ) 0xe000ed04 ) )
+    #define portNVIC_PENDSVSET_BIT    ( 1UL << 28UL )
+    #define portEND_SWITCHING_ISR( xSwitchRequired )    do { if( xSwitchRequired != pdFALSE ) portYIELD(); } while( 0 )
+    #define portYIELD_FROM_ISR( x )                     portEND_SWITCHING_ISR( x )
+/*-----------------------------------------------------------*/
+
+/* Critical section management. */
+    extern void vPortEnterCritical( void );
+    extern void vPortExitCritical( void );
+
+    #define portDISABLE_INTERRUPTS()                  vPortRaiseBASEPRI()
+    #define portENABLE_INTERRUPTS()                   vPortSetBASEPRI( 0 )
+    #define portENTER_CRITICAL()                      vPortEnterCritical()
+    #define portEXIT_CRITICAL()                       vPortExitCritical()
+    #define portSET_INTERRUPT_MASK_FROM_ISR()         ulPortRaiseBASEPRI()
+    #define portCLEAR_INTERRUPT_MASK_FROM_ISR( x )    vPortSetBASEPRI( x )
+
+/*-----------------------------------------------------------*/
+
+/* Tickless idle/low power functionality. */
+    #ifndef portSUPPRESS_TICKS_AND_SLEEP
+        extern void vPortSuppressTicksAndSleep( TickType_t xExpectedIdleTime );
+        #define portSUPPRESS_TICKS_AND_SLEEP( xExpectedIdleTime )    vPortSuppressTicksAndSleep( xExpectedIdleTime )
+    #endif
+/*-----------------------------------------------------------*/
+
+/* Port specific optimisations. */
+    #ifndef configUSE_PORT_OPTIMISED_TASK_SELECTION
+        #define configUSE_PORT_OPTIMISED_TASK_SELECTION    1
+    #endif
+
+    #if configUSE_PORT_OPTIMISED_TASK_SELECTION == 1
+
+/* Check the configuration. */
+        #if ( configMAX_PRIORITIES > 32 )
+            #error configUSE_PORT_OPTIMISED_TASK_SELECTION can only be set to 1 when configMAX_PRIORITIES is less than or equal to 32.  It is very rare that a system requires more than 10 to 15 difference priorities as tasks that share a priority will time slice.
+        #endif
+
+/* Store/clear the ready priorities in a bit map. */
+        #define portRECORD_READY_PRIORITY( uxPriority, uxReadyPriorities )    ( uxReadyPriorities ) |= ( 1UL << ( uxPriority ) )
+        #define portRESET_READY_PRIORITY( uxPriority, uxReadyPriorities )     ( uxReadyPriorities ) &= ~( 1UL << ( uxPriority ) )
+
+/*-----------------------------------------------------------*/
+
+        #define portGET_HIGHEST_PRIORITY( uxTopPriority, uxReadyPriorities )    uxTopPriority = ( 31UL - ( uint32_t ) __clz( ( uxReadyPriorities ) ) )
+
+    #endif /* taskRECORD_READY_PRIORITY */
+/*-----------------------------------------------------------*/
+
+/* Task function macros as described on the FreeRTOS.org WEB site.  These are
+ * not necessary for to use this port.  They are defined so the common demo files
+ * (which build with all the ports) will build. */
+    #define portTASK_FUNCTION_PROTO( vFunction, pvParameters )    void vFunction( void * pvParameters )
+    #define portTASK_FUNCTION( vFunction, pvParameters )          void vFunction( void * pvParameters )
+/*-----------------------------------------------------------*/
+
+    #ifdef configASSERT
+        void vPortValidateInterruptPriority( void );
+        #define portASSERT_IF_INTERRUPT_PRIORITY_INVALID()    vPortValidateInterruptPriority()
+    #endif
+
+/* portNOP() is not required by this port. */
+    #define portNOP()
+
+    #define portINLINE              __inline
+
+    #ifndef portFORCE_INLINE
+        #define portFORCE_INLINE    __forceinline
+    #endif
+
+/*-----------------------------------------------------------*/
+
+    static portFORCE_INLINE void vPortSetBASEPRI( uint32_t ulBASEPRI )
+    {
+        __asm
+        {
+            /* Barrier instructions are not used as this function is only used to
+             * lower the BASEPRI value. */
+/* *INDENT-OFF* */
+            msr basepri, ulBASEPRI
+/* *INDENT-ON* */
+        }
+    }
+/*-----------------------------------------------------------*/
+
+    static portFORCE_INLINE void vPortRaiseBASEPRI( void )
+    {
+        uint32_t ulNewBASEPRI = configMAX_SYSCALL_INTERRUPT_PRIORITY;
+
+        __asm
+        {
+            /* Set BASEPRI to the max syscall priority to effect a critical
+             * section. */
+/* *INDENT-OFF* */
+            msr basepri, ulNewBASEPRI
+            dsb
+            isb
+/* *INDENT-ON* */
+        }
+    }
+/*-----------------------------------------------------------*/
+
+    static portFORCE_INLINE void vPortClearBASEPRIFromISR( void )
+    {
+        __asm
+        {
+            /* Set BASEPRI to 0 so no interrupts are masked.  This function is only
+             * used to lower the mask in an interrupt, so memory barriers are not
+             * used. */
+/* *INDENT-OFF* */
+            msr basepri, # 0
+/* *INDENT-ON* */
+        }
+    }
+/*-----------------------------------------------------------*/
+
+    static portFORCE_INLINE uint32_t ulPortRaiseBASEPRI( void )
+    {
+        uint32_t ulReturn, ulNewBASEPRI = configMAX_SYSCALL_INTERRUPT_PRIORITY;
+
+        __asm
+        {
+            /* Set BASEPRI to the max syscall priority to effect a critical
+             * section. */
+/* *INDENT-OFF* */
+            mrs ulReturn, basepri
+            msr basepri, ulNewBASEPRI
+            dsb
+            isb
+/* *INDENT-ON* */
+        }
+
+        return ulReturn;
+    }
+/*-----------------------------------------------------------*/
+
+    static portFORCE_INLINE BaseType_t xPortIsInsideInterrupt( void )
+    {
+        uint32_t ulCurrentInterrupt;
+        BaseType_t xReturn;
+
+        /* Obtain the number of the currently executing interrupt. */
+        __asm
+        {
+/* *INDENT-OFF* */
+            mrs ulCurrentInterrupt, ipsr
+/* *INDENT-ON* */
+        }
+
+        if( ulCurrentInterrupt == 0 )
+        {
+            xReturn = pdFALSE;
+        }
+        else
+        {
+            xReturn = pdTRUE;
+        }
+
+        return xReturn;
+    }
+
+
+/* *INDENT-OFF* */
+#ifdef __cplusplus
+    }
+#endif
+/* *INDENT-ON* */
+
+#endif /* PORTMACRO_H */

Hardware/PWM.c

+#include "stm32f10x.h"                  // Device header
+
+void PWM_Init(void)
+{
+	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
+	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
+	
+	GPIO_InitTypeDef GPIO_InitStructure;
+	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
+	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2|GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_3;
+	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
+	GPIO_Init(GPIOA, &GPIO_InitStructure);
+	
+	TIM_InternalClockConfig(TIM2);
+	
+	TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStructure;
+	TIM_TimeBaseInitStructure.TIM_ClockDivision = TIM_CKD_DIV1;
+	TIM_TimeBaseInitStructure.TIM_CounterMode = TIM_CounterMode_Up;
+	TIM_TimeBaseInitStructure.TIM_Period = 100 - 1;		//ARR
+	TIM_TimeBaseInitStructure.TIM_Prescaler = 7200-1;		//PSC
+	TIM_TimeBaseInitStructure.TIM_RepetitionCounter = 0;
+	TIM_TimeBaseInit(TIM2, &TIM_TimeBaseInitStructure);
+	
+	TIM_OCInitTypeDef TIM_OCInitStructure;
+	TIM_OCStructInit(&TIM_OCInitStructure);
+	TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
+	TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
+	TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
+	TIM_OCInitStructure.TIM_Pulse = 0;		//CCR
+	TIM_OC1Init(TIM2, &TIM_OCInitStructure);
+	TIM_OC2Init(TIM2, &TIM_OCInitStructure);
+	TIM_OC3Init(TIM2, &TIM_OCInitStructure);
+	TIM_OC4Init(TIM2, &TIM_OCInitStructure);
+	
+	TIM_Cmd(TIM2, ENABLE);
+	
+}
+
+void PWM_SetCompare1(uint16_t Compare)
+{
+	TIM_SetCompare1(TIM2, Compare);
+}
+
+void PWM_SetCompare2(uint16_t Compare)
+{
+	TIM_SetCompare2(TIM2, Compare);
+}
+
+void PWM_SetCompare3(uint16_t Compare)
+{
+	TIM_SetCompare3(TIM2, Compare);
+}
+
+void PWM_SetCompare4(uint16_t Compare)
+{
+	TIM_SetCompare4(TIM2, Compare);
+}

Hardware/PWM.h

+#ifndef __PWM_H
+#define __PWM_H
+
+void PWM_Init(void);
+void PWM_SetCompare1(uint16_t Compare);
+void PWM_SetCompare2(uint16_t Compare);
+void PWM_SetCompare3(uint16_t Compare);
+void PWM_SetCompare4(uint16_t Compare);
+#endif

Hardware/Serial.c

+#include "stm32f10x.h"                  // Device header
+#include <stdio.h>
+#include <stdarg.h>
+#include <stdlib.h>
+#include <string.h>
+#include "Delay.h"
+
+uint8_t Serial_TxPacket[6];
+uint8_t Serial_RxFlag;
+uint8_t Serial_RxPacket[6];
+
+
+/**
+  * 函    数：串口初始化
+  * 参    数：无
+  * 返 回 值：无
+  */
+void Serial_Init(void)
+{
+	/*开启时钟*/
+	RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);	//开启USART1的时钟
+	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);	//开启GPIOA的时钟
+	
+	/*GPIO初始化*/
+	GPIO_InitTypeDef GPIO_InitStructure;
+	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
+	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
+	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
+	GPIO_Init(GPIOA, &GPIO_InitStructure);					//将PA9引脚初始化为复用推挽输出
+	
+	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
+	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
+	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
+	GPIO_Init(GPIOA, &GPIO_InitStructure);					//将PA10引脚初始化为上拉输入
+	
+	/*USART初始化*/
+	USART_InitTypeDef USART_InitStructure;					//定义结构体变量
+	USART_InitStructure.USART_BaudRate = 9600;				//波特率
+	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;	//硬件流控制，不需要
+	USART_InitStructure.USART_Mode = USART_Mode_Tx | USART_Mode_Rx;	//模式，发送模式和接收模式均选择
+	USART_InitStructure.USART_Parity = USART_Parity_No;		//奇偶校验，不需要
+	USART_InitStructure.USART_StopBits = USART_StopBits_1;	//停止位，选择1位
+	USART_InitStructure.USART_WordLength = USART_WordLength_8b;		//字长，选择8位
+	USART_Init(USART1, &USART_InitStructure);				//将结构体变量交给USART_Init，配置USART1
+	
+	/*中断输出配置*/
+	USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);			//开启串口接收数据的中断
+	
+	/*NVIC中断分组*/
+	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);			//配置NVIC为分组2
+	
+	/*NVIC配置*/
+	NVIC_InitTypeDef NVIC_InitStructure;					//定义结构体变量
+	NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;		//选择配置NVIC的USART1线
+	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;			//指定NVIC线路使能
+	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 5;		//指定NVIC线路的抢占优先级为1
+	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;		//指定NVIC线路的响应优先级为1
+	NVIC_Init(&NVIC_InitStructure);							//将结构体变量交给NVIC_Init，配置NVIC外设
+	
+	/*USART使能*/
+	USART_Cmd(USART1, ENABLE);								//使能USART1，串口开始运行
+}
+
+
+void Serial_SendByte(uint8_t Byte)
+{
+	USART_SendData(USART1, Byte);		//将字节数据写入数据寄存器，写入后USART自动生成时序波形
+	while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);	//等待发送完成
+	
+}
+
+
+
+void Serial_SendString(char *String)
+{
+	uint8_t i;
+	for (i = 0; String[i] != '\0'; i++)//遍历字符数组（字符串），遇到字符串结束标志位后停止
+	{
+		Serial_SendByte(String[i]);		//依次调用Serial_SendByte发送每个字节数据
+	}
+}
+
+void Serial_SendArray(uint8_t *Array, uint16_t Length)
+{
+	uint16_t i;
+	for (i = 0; i < Length; i ++)		//遍历数组
+	{
+		Serial_SendByte(Array[i]);		//依次调用Serial_SendByte发送每个字节数据
+	}
+}
+
+
+
+int fputc(int ch, FILE *f)
+{
+	Serial_SendByte(ch);			//将printf的底层重定向到自己的发送字节函数
+	return ch;
+}
+
+
+void Serial_Printf(char *format, ...)
+{
+	char String[100];				//定义字符数组
+	va_list arg;					//定义可变参数列表数据类型的变量arg
+	va_start(arg, format);			//从format开始，接收参数列表到arg变量
+	vsprintf(String, format, arg);	//使用vsprintf打印格式化字符串和参数列表到字符数组中
+	va_end(arg);					//结束变量arg
+	Serial_SendString(String);		//串口发送字符数组（字符串）
+}
+
+/*将数字转化为字符串发送出去*/
+void USART1_SendNumber(int number) {
+    char buffer[16];
+    sprintf(buffer, "%d\n", number); // 将数字转为字符串
+	Delay_ms(200);
+    for (char *ptr = buffer; *ptr != '\0'; ptr++) {
+        USART_SendData(USART1, *ptr);
+        while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
+    }
+}
+
+
+
+
+
+uint8_t Serial_GetRxFlag(void)
+{
+	if (Serial_RxFlag == 1)			//如果标志位为1
+	{
+		Serial_RxFlag = 0;
+		return 1;					//则返回1，并自动清零标志位
+	}
+	return 0;						//如果标志位为0，则返回0
+}
+
+void Serial_SendPacket(void)
+{
+	Serial_SendByte(0xAA);
+	Serial_SendArray(Serial_TxPacket, 5);
+	Serial_SendByte(0xFE);
+}
+
+
+
+
+
+void USART1_IRQHandler(void)
+{
+	
+	static uint8_t RxState = 0;
+	static uint8_t pRxPacket = 0;
+	if (USART_GetITStatus(USART1, USART_IT_RXNE) == SET)
+	{
+		uint8_t RxData = USART_ReceiveData(USART1);
+		//Serial_SendString("ad");
+		if (RxState == 0)
+		{
+			if (RxData == 0xAA)
+			{
+				RxState = 1;
+				pRxPacket = 0;
+			}
+		}
+		else if (RxState == 1)
+		{
+			Serial_RxPacket[pRxPacket]=RxData;
+			pRxPacket++;
+			if (pRxPacket>= 3)
+			{
+				RxState = 2;
+			}
+			
+		}
+		else if (RxState == 2)
+		{
+			if (RxData == 0xFE)
+			{
+				RxState = 0;
+				
+				Serial_RxFlag = 1;
+			}
+		}
+		
+		USART_ClearITPendingBit(USART1, USART_IT_RXNE);
+	}
+
+}

Hardware/Serial.h

+#ifndef __SERIAL_H
+#define __SERIAL_H
+
+#include <stdio.h>
+
+
+
+void Serial_Init(void);
+void Serial_SendByte(uint8_t Byte);
+void Serial_SendArray(uint8_t *Array, uint16_t Length);
+void Serial_SendString(char *String);
+void Serial_SendNumber(uint32_t Number, uint8_t Length);
+void Serial_Printf(char *format, ...);
+void USART1_SendNumber(int number);
+
+uint8_t Serial_GetRxFlag(void);
+char Serial_GetRxData(void);
+void Serial_ReceivedData(char *buffer);
+
+extern uint8_t Serial_RxPacket[];
+extern uint8_t Serial_RxFlag;
+extern uint8_t Serial_TxPacket[];
+void Serial_SendPacket(void);
+
+
+#endif

Hardware/pin.c

+#include "stm32f10x.h"                  // Device header
+#include "Serial.h"
+
+void pin_Init(void)
+{
+	/*ʱ*/
+	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);	
+	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);					
+	GPIO_InitTypeDef GPIO_InitStructure;					
+	
+	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;		
+	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12|GPIO_Pin_13;				
+	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;		
+	
+		
+	
+	GPIO_InitTypeDef GPIO_InitStructureIn;
+	GPIO_InitStructureIn.GPIO_Mode = GPIO_Mode_IPU;
+	GPIO_InitStructureIn.GPIO_Pin = GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;
+	GPIO_InitStructureIn.GPIO_Speed = GPIO_Speed_50MHz;
+	
+	
+	GPIO_Init(GPIOB, &GPIO_InitStructure);
+	GPIO_Init(GPIOA, &GPIO_InitStructureIn);	
+									
+}
+
+int pinBSet(int pinx,int Setpin)
+{
+	
+	if(Setpin==0 )
+	{
+		switch(pinx)
+		{
+			case 10:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_RESET);
+				//Serial_SendString("B10:LOW");
+				break;
+			case 11:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_11, Bit_RESET);
+				//Serial_SendString("B11:LOW");
+				break;
+			case 12:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_12, Bit_RESET);
+				//Serial_SendString("B12:LOW");
+				break;
+			case 13:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_13, Bit_RESET);
+				//Serial_SendString("B13:LOW");
+				break;
+			default:
+				break;
+		}
+		
+	}
+	
+	if(Setpin==1 )
+	{
+		switch(pinx)
+		{
+			case 10:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_SET);
+				//Serial_SendString("B10:HIGH");
+				break;
+			case 11:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_11, Bit_SET);
+				//Serial_SendString("B11:HIGH");
+				break;
+			case 12:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_12, Bit_SET);
+				//Serial_SendString("B12:HIGH");
+				break;
+			case 13:
+				GPIO_WriteBit(GPIOB, GPIO_Pin_13, Bit_SET);
+				//Serial_SendString("B13:HIGH");
+				break;
+			default:
+				break;
+		}
+		
+	}
+	return pinx;
+}
+
+int Read_Apin(void)
+{
+	if(GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_4)==0)
+	{
+		
+		return 1;
+		
+	}
+	if(GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_5)==0)
+	{
+		
+		return 2;
+		
+	}
+	if(GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_6)==0)
+	{
+		
+		return 3;
+	}
+	if(GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_7)==0)
+	{
+		
+		return 4;
+	}
+	return 0;
+}

Hardware/pin.h

+#ifndef __PIN_H
+#define __PIN_H
+
+
+void pin_Init(void);
+void pinBSet(int pinx,int Setpin);
+int Read_Apin(void);
+#endif

Library/misc.c

+/**
+  ******************************************************************************
+  * @file    misc.c
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file provides all the miscellaneous firmware functions (add-on
+  *          to CMSIS functions).
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "misc.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup MISC 
+  * @brief MISC driver modules
+  * @{
+  */
+
+/** @defgroup MISC_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/** @defgroup MISC_Private_Defines
+  * @{
+  */
+
+#define AIRCR_VECTKEY_MASK    ((uint32_t)0x05FA0000)
+/**
+  * @}
+  */
+
+/** @defgroup MISC_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup MISC_Private_Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup MISC_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup MISC_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Configures the priority grouping: pre-emption priority and subpriority.
+  * @param  NVIC_PriorityGroup: specifies the priority grouping bits length. 
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_PriorityGroup_0: 0 bits for pre-emption priority
+  *                                4 bits for subpriority
+  *     @arg NVIC_PriorityGroup_1: 1 bits for pre-emption priority
+  *                                3 bits for subpriority
+  *     @arg NVIC_PriorityGroup_2: 2 bits for pre-emption priority
+  *                                2 bits for subpriority
+  *     @arg NVIC_PriorityGroup_3: 3 bits for pre-emption priority
+  *                                1 bits for subpriority
+  *     @arg NVIC_PriorityGroup_4: 4 bits for pre-emption priority
+  *                                0 bits for subpriority
+  * @retval None
+  */
+void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_PRIORITY_GROUP(NVIC_PriorityGroup));
+  
+  /* Set the PRIGROUP[10:8] bits according to NVIC_PriorityGroup value */
+  SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup;
+}
+
+/**
+  * @brief  Initializes the NVIC peripheral according to the specified
+  *         parameters in the NVIC_InitStruct.
+  * @param  NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains
+  *         the configuration information for the specified NVIC peripheral.
+  * @retval None
+  */
+void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct)
+{
+  uint32_t tmppriority = 0x00, tmppre = 0x00, tmpsub = 0x0F;
+  
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NVIC_InitStruct->NVIC_IRQChannelCmd));
+  assert_param(IS_NVIC_PREEMPTION_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority));  
+  assert_param(IS_NVIC_SUB_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelSubPriority));
+    
+  if (NVIC_InitStruct->NVIC_IRQChannelCmd != DISABLE)
+  {
+    /* Compute the Corresponding IRQ Priority --------------------------------*/    
+    tmppriority = (0x700 - ((SCB->AIRCR) & (uint32_t)0x700))>> 0x08;
+    tmppre = (0x4 - tmppriority);
+    tmpsub = tmpsub >> tmppriority;
+
+    tmppriority = (uint32_t)NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority << tmppre;
+    tmppriority |=  NVIC_InitStruct->NVIC_IRQChannelSubPriority & tmpsub;
+    tmppriority = tmppriority << 0x04;
+        
+    NVIC->IP[NVIC_InitStruct->NVIC_IRQChannel] = tmppriority;
+    
+    /* Enable the Selected IRQ Channels --------------------------------------*/
+    NVIC->ISER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+  else
+  {
+    /* Disable the Selected IRQ Channels -------------------------------------*/
+    NVIC->ICER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+}
+
+/**
+  * @brief  Sets the vector table location and Offset.
+  * @param  NVIC_VectTab: specifies if the vector table is in RAM or FLASH memory.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_VectTab_RAM
+  *     @arg NVIC_VectTab_FLASH
+  * @param  Offset: Vector Table base offset field. This value must be a multiple 
+  *         of 0x200.
+  * @retval None
+  */
+void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset)
+{ 
+  /* Check the parameters */
+  assert_param(IS_NVIC_VECTTAB(NVIC_VectTab));
+  assert_param(IS_NVIC_OFFSET(Offset));  
+   
+  SCB->VTOR = NVIC_VectTab | (Offset & (uint32_t)0x1FFFFF80);
+}
+
+/**
+  * @brief  Selects the condition for the system to enter low power mode.
+  * @param  LowPowerMode: Specifies the new mode for the system to enter low power mode.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_LP_SEVONPEND
+  *     @arg NVIC_LP_SLEEPDEEP
+  *     @arg NVIC_LP_SLEEPONEXIT
+  * @param  NewState: new state of LP condition. This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_LP(LowPowerMode));
+  assert_param(IS_FUNCTIONAL_STATE(NewState));  
+  
+  if (NewState != DISABLE)
+  {
+    SCB->SCR |= LowPowerMode;
+  }
+  else
+  {
+    SCB->SCR &= (uint32_t)(~(uint32_t)LowPowerMode);
+  }
+}
+
+/**
+  * @brief  Configures the SysTick clock source.
+  * @param  SysTick_CLKSource: specifies the SysTick clock source.
+  *   This parameter can be one of the following values:
+  *     @arg SysTick_CLKSource_HCLK_Div8: AHB clock divided by 8 selected as SysTick clock source.
+  *     @arg SysTick_CLKSource_HCLK: AHB clock selected as SysTick clock source.
+  * @retval None
+  */
+void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource)
+{
+  /* Check the parameters */
+  assert_param(IS_SYSTICK_CLK_SOURCE(SysTick_CLKSource));
+  if (SysTick_CLKSource == SysTick_CLKSource_HCLK)
+  {
+    SysTick->CTRL |= SysTick_CLKSource_HCLK;
+  }
+  else
+  {
+    SysTick->CTRL &= SysTick_CLKSource_HCLK_Div8;
+  }
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/misc.h

+/**
+  ******************************************************************************
+  * @file    misc.h
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file contains all the functions prototypes for the miscellaneous
+  *          firmware library functions (add-on to CMSIS functions).
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __MISC_H
+#define __MISC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @addtogroup MISC
+  * @{
+  */
+
+/** @defgroup MISC_Exported_Types
+  * @{
+  */
+
+/** 
+  * @brief  NVIC Init Structure definition  
+  */
+
+typedef struct
+{
+  uint8_t NVIC_IRQChannel;                    /*!< Specifies the IRQ channel to be enabled or disabled.
+                                                   This parameter can be a value of @ref IRQn_Type 
+                                                   (For the complete STM32 Devices IRQ Channels list, please
+                                                    refer to stm32f10x.h file) */
+
+  uint8_t NVIC_IRQChannelPreemptionPriority;  /*!< Specifies the pre-emption priority for the IRQ channel
+                                                   specified in NVIC_IRQChannel. This parameter can be a value
+                                                   between 0 and 15 as described in the table @ref NVIC_Priority_Table */
+
+  uint8_t NVIC_IRQChannelSubPriority;         /*!< Specifies the subpriority level for the IRQ channel specified
+                                                   in NVIC_IRQChannel. This parameter can be a value
+                                                   between 0 and 15 as described in the table @ref NVIC_Priority_Table */
+
+  FunctionalState NVIC_IRQChannelCmd;         /*!< Specifies whether the IRQ channel defined in NVIC_IRQChannel
+                                                   will be enabled or disabled. 
+                                                   This parameter can be set either to ENABLE or DISABLE */   
+} NVIC_InitTypeDef;
+ 
+/**
+  * @}
+  */
+
+/** @defgroup NVIC_Priority_Table 
+  * @{
+  */
+
+/**
+@code  
+ The table below gives the allowed values of the pre-emption priority and subpriority according
+ to the Priority Grouping configuration performed by NVIC_PriorityGroupConfig function
+  ============================================================================================================================
+    NVIC_PriorityGroup   | NVIC_IRQChannelPreemptionPriority | NVIC_IRQChannelSubPriority  | Description
+  ============================================================================================================================
+   NVIC_PriorityGroup_0  |                0                  |            0-15             |   0 bits for pre-emption priority
+                         |                                   |                             |   4 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------
+   NVIC_PriorityGroup_1  |                0-1                |            0-7              |   1 bits for pre-emption priority
+                         |                                   |                             |   3 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------    
+   NVIC_PriorityGroup_2  |                0-3                |            0-3              |   2 bits for pre-emption priority
+                         |                                   |                             |   2 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------    
+   NVIC_PriorityGroup_3  |                0-7                |            0-1              |   3 bits for pre-emption priority
+                         |                                   |                             |   1 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------    
+   NVIC_PriorityGroup_4  |                0-15               |            0                |   4 bits for pre-emption priority
+                         |                                   |                             |   0 bits for subpriority                       
+  ============================================================================================================================
+@endcode
+*/
+
+/**
+  * @}
+  */
+
+/** @defgroup MISC_Exported_Constants
+  * @{
+  */
+
+/** @defgroup Vector_Table_Base 
+  * @{
+  */
+
+#define NVIC_VectTab_RAM             ((uint32_t)0x20000000)
+#define NVIC_VectTab_FLASH           ((uint32_t)0x08000000)
+#define IS_NVIC_VECTTAB(VECTTAB) (((VECTTAB) == NVIC_VectTab_RAM) || \
+                                  ((VECTTAB) == NVIC_VectTab_FLASH))
+/**
+  * @}
+  */
+
+/** @defgroup System_Low_Power 
+  * @{
+  */
+
+#define NVIC_LP_SEVONPEND            ((uint8_t)0x10)
+#define NVIC_LP_SLEEPDEEP            ((uint8_t)0x04)
+#define NVIC_LP_SLEEPONEXIT          ((uint8_t)0x02)
+#define IS_NVIC_LP(LP) (((LP) == NVIC_LP_SEVONPEND) || \
+                        ((LP) == NVIC_LP_SLEEPDEEP) || \
+                        ((LP) == NVIC_LP_SLEEPONEXIT))
+/**
+  * @}
+  */
+
+/** @defgroup Preemption_Priority_Group 
+  * @{
+  */
+
+#define NVIC_PriorityGroup_0         ((uint32_t)0x700) /*!< 0 bits for pre-emption priority
+                                                            4 bits for subpriority */
+#define NVIC_PriorityGroup_1         ((uint32_t)0x600) /*!< 1 bits for pre-emption priority
+                                                            3 bits for subpriority */
+#define NVIC_PriorityGroup_2         ((uint32_t)0x500) /*!< 2 bits for pre-emption priority
+                                                            2 bits for subpriority */
+#define NVIC_PriorityGroup_3         ((uint32_t)0x400) /*!< 3 bits for pre-emption priority
+                                                            1 bits for subpriority */
+#define NVIC_PriorityGroup_4         ((uint32_t)0x300) /*!< 4 bits for pre-emption priority
+                                                            0 bits for subpriority */
+
+#define IS_NVIC_PRIORITY_GROUP(GROUP) (((GROUP) == NVIC_PriorityGroup_0) || \
+                                       ((GROUP) == NVIC_PriorityGroup_1) || \
+                                       ((GROUP) == NVIC_PriorityGroup_2) || \
+                                       ((GROUP) == NVIC_PriorityGroup_3) || \
+                                       ((GROUP) == NVIC_PriorityGroup_4))
+
+#define IS_NVIC_PREEMPTION_PRIORITY(PRIORITY)  ((PRIORITY) < 0x10)
+
+#define IS_NVIC_SUB_PRIORITY(PRIORITY)  ((PRIORITY) < 0x10)
+
+#define IS_NVIC_OFFSET(OFFSET)  ((OFFSET) < 0x000FFFFF)
+
+/**
+  * @}
+  */
+
+/** @defgroup SysTick_clock_source 
+  * @{
+  */
+
+#define SysTick_CLKSource_HCLK_Div8    ((uint32_t)0xFFFFFFFB)
+#define SysTick_CLKSource_HCLK         ((uint32_t)0x00000004)
+#define IS_SYSTICK_CLK_SOURCE(SOURCE) (((SOURCE) == SysTick_CLKSource_HCLK) || \
+                                       ((SOURCE) == SysTick_CLKSource_HCLK_Div8))
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup MISC_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup MISC_Exported_Functions
+  * @{
+  */
+
+void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup);
+void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct);
+void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset);
+void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState);
+void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MISC_H */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_bkp.c

+/**
+  ******************************************************************************
+  * @file    stm32f10x_bkp.c
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file provides all the BKP firmware functions.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_bkp.h"
+#include "stm32f10x_rcc.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup BKP 
+  * @brief BKP driver modules
+  * @{
+  */
+
+/** @defgroup BKP_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup BKP_Private_Defines
+  * @{
+  */
+
+/* ------------ BKP registers bit address in the alias region --------------- */
+#define BKP_OFFSET        (BKP_BASE - PERIPH_BASE)
+
+/* --- CR Register ----*/
+
+/* Alias word address of TPAL bit */
+#define CR_OFFSET         (BKP_OFFSET + 0x30)
+#define TPAL_BitNumber    0x01
+#define CR_TPAL_BB        (PERIPH_BB_BASE + (CR_OFFSET * 32) + (TPAL_BitNumber * 4))
+
+/* Alias word address of TPE bit */
+#define TPE_BitNumber     0x00
+#define CR_TPE_BB         (PERIPH_BB_BASE + (CR_OFFSET * 32) + (TPE_BitNumber * 4))
+
+/* --- CSR Register ---*/
+
+/* Alias word address of TPIE bit */
+#define CSR_OFFSET        (BKP_OFFSET + 0x34)
+#define TPIE_BitNumber    0x02
+#define CSR_TPIE_BB       (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (TPIE_BitNumber * 4))
+
+/* Alias word address of TIF bit */
+#define TIF_BitNumber     0x09
+#define CSR_TIF_BB        (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (TIF_BitNumber * 4))
+
+/* Alias word address of TEF bit */
+#define TEF_BitNumber     0x08
+#define CSR_TEF_BB        (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (TEF_BitNumber * 4))
+
+/* ---------------------- BKP registers bit mask ------------------------ */
+
+/* RTCCR register bit mask */
+#define RTCCR_CAL_MASK    ((uint16_t)0xFF80)
+#define RTCCR_MASK        ((uint16_t)0xFC7F)
+
+/**
+  * @}
+  */ 
+
+
+/** @defgroup BKP_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup BKP_Private_Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup BKP_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup BKP_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Deinitializes the BKP peripheral registers to their default reset values.
+  * @param  None
+  * @retval None
+  */
+void BKP_DeInit(void)
+{
+  RCC_BackupResetCmd(ENABLE);
+  RCC_BackupResetCmd(DISABLE);
+}
+
+/**
+  * @brief  Configures the Tamper Pin active level.
+  * @param  BKP_TamperPinLevel: specifies the Tamper Pin active level.
+  *   This parameter can be one of the following values:
+  *     @arg BKP_TamperPinLevel_High: Tamper pin active on high level
+  *     @arg BKP_TamperPinLevel_Low: Tamper pin active on low level
+  * @retval None
+  */
+void BKP_TamperPinLevelConfig(uint16_t BKP_TamperPinLevel)
+{
+  /* Check the parameters */
+  assert_param(IS_BKP_TAMPER_PIN_LEVEL(BKP_TamperPinLevel));
+  *(__IO uint32_t *) CR_TPAL_BB = BKP_TamperPinLevel;
+}
+
+/**
+  * @brief  Enables or disables the Tamper Pin activation.
+  * @param  NewState: new state of the Tamper Pin activation.
+  *   This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void BKP_TamperPinCmd(FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NewState));
+  *(__IO uint32_t *) CR_TPE_BB = (uint32_t)NewState;
+}
+
+/**
+  * @brief  Enables or disables the Tamper Pin Interrupt.
+  * @param  NewState: new state of the Tamper Pin Interrupt.
+  *   This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void BKP_ITConfig(FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NewState));
+  *(__IO uint32_t *) CSR_TPIE_BB = (uint32_t)NewState;
+}
+
+/**
+  * @brief  Select the RTC output source to output on the Tamper pin.
+  * @param  BKP_RTCOutputSource: specifies the RTC output source.
+  *   This parameter can be one of the following values:
+  *     @arg BKP_RTCOutputSource_None: no RTC output on the Tamper pin.
+  *     @arg BKP_RTCOutputSource_CalibClock: output the RTC clock with frequency
+  *                                          divided by 64 on the Tamper pin.
+  *     @arg BKP_RTCOutputSource_Alarm: output the RTC Alarm pulse signal on
+  *                                     the Tamper pin.
+  *     @arg BKP_RTCOutputSource_Second: output the RTC Second pulse signal on
+  *                                      the Tamper pin.  
+  * @retval None
+  */
+void BKP_RTCOutputConfig(uint16_t BKP_RTCOutputSource)
+{
+  uint16_t tmpreg = 0;
+  /* Check the parameters */
+  assert_param(IS_BKP_RTC_OUTPUT_SOURCE(BKP_RTCOutputSource));
+  tmpreg = BKP->RTCCR;
+  /* Clear CCO, ASOE and ASOS bits */
+  tmpreg &= RTCCR_MASK;
+  
+  /* Set CCO, ASOE and ASOS bits according to BKP_RTCOutputSource value */
+  tmpreg |= BKP_RTCOutputSource;
+  /* Store the new value */
+  BKP->RTCCR = tmpreg;
+}
+
+/**
+  * @brief  Sets RTC Clock Calibration value.
+  * @param  CalibrationValue: specifies the RTC Clock Calibration value.
+  *   This parameter must be a number between 0 and 0x7F.
+  * @retval None
+  */
+void BKP_SetRTCCalibrationValue(uint8_t CalibrationValue)
+{
+  uint16_t tmpreg = 0;
+  /* Check the parameters */
+  assert_param(IS_BKP_CALIBRATION_VALUE(CalibrationValue));
+  tmpreg = BKP->RTCCR;
+  /* Clear CAL[6:0] bits */
+  tmpreg &= RTCCR_CAL_MASK;
+  /* Set CAL[6:0] bits according to CalibrationValue value */
+  tmpreg |= CalibrationValue;
+  /* Store the new value */
+  BKP->RTCCR = tmpreg;
+}
+
+/**
+  * @brief  Writes user data to the specified Data Backup Register.
+  * @param  BKP_DR: specifies the Data Backup Register.
+  *   This parameter can be BKP_DRx where x:[1, 42]
+  * @param  Data: data to write
+  * @retval None
+  */
+void BKP_WriteBackupRegister(uint16_t BKP_DR, uint16_t Data)
+{
+  __IO uint32_t tmp = 0;
+
+  /* Check the parameters */
+  assert_param(IS_BKP_DR(BKP_DR));
+
+  tmp = (uint32_t)BKP_BASE; 
+  tmp += BKP_DR;
+
+  *(__IO uint32_t *) tmp = Data;
+}
+
+/**
+  * @brief  Reads data from the specified Data Backup Register.
+  * @param  BKP_DR: specifies the Data Backup Register.
+  *   This parameter can be BKP_DRx where x:[1, 42]
+  * @retval The content of the specified Data Backup Register
+  */
+uint16_t BKP_ReadBackupRegister(uint16_t BKP_DR)
+{
+  __IO uint32_t tmp = 0;
+
+  /* Check the parameters */
+  assert_param(IS_BKP_DR(BKP_DR));
+
+  tmp = (uint32_t)BKP_BASE; 
+  tmp += BKP_DR;
+
+  return (*(__IO uint16_t *) tmp);
+}
+
+/**
+  * @brief  Checks whether the Tamper Pin Event flag is set or not.
+  * @param  None
+  * @retval The new state of the Tamper Pin Event flag (SET or RESET).
+  */
+FlagStatus BKP_GetFlagStatus(void)
+{
+  return (FlagStatus)(*(__IO uint32_t *) CSR_TEF_BB);
+}
+
+/**
+  * @brief  Clears Tamper Pin Event pending flag.
+  * @param  None
+  * @retval None
+  */
+void BKP_ClearFlag(void)
+{
+  /* Set CTE bit to clear Tamper Pin Event flag */
+  BKP->CSR |= BKP_CSR_CTE;
+}
+
+/**
+  * @brief  Checks whether the Tamper Pin Interrupt has occurred or not.
+  * @param  None
+  * @retval The new state of the Tamper Pin Interrupt (SET or RESET).
+  */
+ITStatus BKP_GetITStatus(void)
+{
+  return (ITStatus)(*(__IO uint32_t *) CSR_TIF_BB);
+}
+
+/**
+  * @brief  Clears Tamper Pin Interrupt pending bit.
+  * @param  None
+  * @retval None
+  */
+void BKP_ClearITPendingBit(void)
+{
+  /* Set CTI bit to clear Tamper Pin Interrupt pending bit */
+  BKP->CSR |= BKP_CSR_CTI;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_bkp.h

+/**
+  ******************************************************************************
+  * @file    stm32f10x_bkp.h
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file contains all the functions prototypes for the BKP firmware 
+  *          library.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_BKP_H
+#define __STM32F10x_BKP_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @addtogroup BKP
+  * @{
+  */
+
+/** @defgroup BKP_Exported_Types
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup BKP_Exported_Constants
+  * @{
+  */
+
+/** @defgroup Tamper_Pin_active_level 
+  * @{
+  */
+
+#define BKP_TamperPinLevel_High           ((uint16_t)0x0000)
+#define BKP_TamperPinLevel_Low            ((uint16_t)0x0001)
+#define IS_BKP_TAMPER_PIN_LEVEL(LEVEL) (((LEVEL) == BKP_TamperPinLevel_High) || \
+                                        ((LEVEL) == BKP_TamperPinLevel_Low))
+/**
+  * @}
+  */
+
+/** @defgroup RTC_output_source_to_output_on_the_Tamper_pin 
+  * @{
+  */
+
+#define BKP_RTCOutputSource_None          ((uint16_t)0x0000)
+#define BKP_RTCOutputSource_CalibClock    ((uint16_t)0x0080)
+#define BKP_RTCOutputSource_Alarm         ((uint16_t)0x0100)
+#define BKP_RTCOutputSource_Second        ((uint16_t)0x0300)
+#define IS_BKP_RTC_OUTPUT_SOURCE(SOURCE) (((SOURCE) == BKP_RTCOutputSource_None) || \
+                                          ((SOURCE) == BKP_RTCOutputSource_CalibClock) || \
+                                          ((SOURCE) == BKP_RTCOutputSource_Alarm) || \
+                                          ((SOURCE) == BKP_RTCOutputSource_Second))
+/**
+  * @}
+  */
+
+/** @defgroup Data_Backup_Register 
+  * @{
+  */
+
+#define BKP_DR1                           ((uint16_t)0x0004)
+#define BKP_DR2                           ((uint16_t)0x0008)
+#define BKP_DR3                           ((uint16_t)0x000C)
+#define BKP_DR4                           ((uint16_t)0x0010)
+#define BKP_DR5                           ((uint16_t)0x0014)
+#define BKP_DR6                           ((uint16_t)0x0018)
+#define BKP_DR7                           ((uint16_t)0x001C)
+#define BKP_DR8                           ((uint16_t)0x0020)
+#define BKP_DR9                           ((uint16_t)0x0024)
+#define BKP_DR10                          ((uint16_t)0x0028)
+#define BKP_DR11                          ((uint16_t)0x0040)
+#define BKP_DR12                          ((uint16_t)0x0044)
+#define BKP_DR13                          ((uint16_t)0x0048)
+#define BKP_DR14                          ((uint16_t)0x004C)
+#define BKP_DR15                          ((uint16_t)0x0050)
+#define BKP_DR16                          ((uint16_t)0x0054)
+#define BKP_DR17                          ((uint16_t)0x0058)
+#define BKP_DR18                          ((uint16_t)0x005C)
+#define BKP_DR19                          ((uint16_t)0x0060)
+#define BKP_DR20                          ((uint16_t)0x0064)
+#define BKP_DR21                          ((uint16_t)0x0068)
+#define BKP_DR22                          ((uint16_t)0x006C)
+#define BKP_DR23                          ((uint16_t)0x0070)
+#define BKP_DR24                          ((uint16_t)0x0074)
+#define BKP_DR25                          ((uint16_t)0x0078)
+#define BKP_DR26                          ((uint16_t)0x007C)
+#define BKP_DR27                          ((uint16_t)0x0080)
+#define BKP_DR28                          ((uint16_t)0x0084)
+#define BKP_DR29                          ((uint16_t)0x0088)
+#define BKP_DR30                          ((uint16_t)0x008C)
+#define BKP_DR31                          ((uint16_t)0x0090)
+#define BKP_DR32                          ((uint16_t)0x0094)
+#define BKP_DR33                          ((uint16_t)0x0098)
+#define BKP_DR34                          ((uint16_t)0x009C)
+#define BKP_DR35                          ((uint16_t)0x00A0)
+#define BKP_DR36                          ((uint16_t)0x00A4)
+#define BKP_DR37                          ((uint16_t)0x00A8)
+#define BKP_DR38                          ((uint16_t)0x00AC)
+#define BKP_DR39                          ((uint16_t)0x00B0)
+#define BKP_DR40                          ((uint16_t)0x00B4)
+#define BKP_DR41                          ((uint16_t)0x00B8)
+#define BKP_DR42                          ((uint16_t)0x00BC)
+
+#define IS_BKP_DR(DR) (((DR) == BKP_DR1)  || ((DR) == BKP_DR2)  || ((DR) == BKP_DR3)  || \
+                       ((DR) == BKP_DR4)  || ((DR) == BKP_DR5)  || ((DR) == BKP_DR6)  || \
+                       ((DR) == BKP_DR7)  || ((DR) == BKP_DR8)  || ((DR) == BKP_DR9)  || \
+                       ((DR) == BKP_DR10) || ((DR) == BKP_DR11) || ((DR) == BKP_DR12) || \
+                       ((DR) == BKP_DR13) || ((DR) == BKP_DR14) || ((DR) == BKP_DR15) || \
+                       ((DR) == BKP_DR16) || ((DR) == BKP_DR17) || ((DR) == BKP_DR18) || \
+                       ((DR) == BKP_DR19) || ((DR) == BKP_DR20) || ((DR) == BKP_DR21) || \
+                       ((DR) == BKP_DR22) || ((DR) == BKP_DR23) || ((DR) == BKP_DR24) || \
+                       ((DR) == BKP_DR25) || ((DR) == BKP_DR26) || ((DR) == BKP_DR27) || \
+                       ((DR) == BKP_DR28) || ((DR) == BKP_DR29) || ((DR) == BKP_DR30) || \
+                       ((DR) == BKP_DR31) || ((DR) == BKP_DR32) || ((DR) == BKP_DR33) || \
+                       ((DR) == BKP_DR34) || ((DR) == BKP_DR35) || ((DR) == BKP_DR36) || \
+                       ((DR) == BKP_DR37) || ((DR) == BKP_DR38) || ((DR) == BKP_DR39) || \
+                       ((DR) == BKP_DR40) || ((DR) == BKP_DR41) || ((DR) == BKP_DR42))
+
+#define IS_BKP_CALIBRATION_VALUE(VALUE) ((VALUE) <= 0x7F)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup BKP_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup BKP_Exported_Functions
+  * @{
+  */
+
+void BKP_DeInit(void);
+void BKP_TamperPinLevelConfig(uint16_t BKP_TamperPinLevel);
+void BKP_TamperPinCmd(FunctionalState NewState);
+void BKP_ITConfig(FunctionalState NewState);
+void BKP_RTCOutputConfig(uint16_t BKP_RTCOutputSource);
+void BKP_SetRTCCalibrationValue(uint8_t CalibrationValue);
+void BKP_WriteBackupRegister(uint16_t BKP_DR, uint16_t Data);
+uint16_t BKP_ReadBackupRegister(uint16_t BKP_DR);
+FlagStatus BKP_GetFlagStatus(void);
+void BKP_ClearFlag(void);
+ITStatus BKP_GetITStatus(void);
+void BKP_ClearITPendingBit(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F10x_BKP_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_cec.h

+/**
+  ******************************************************************************
+  * @file    stm32f10x_cec.h
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file contains all the functions prototypes for the CEC firmware 
+  *          library.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_CEC_H
+#define __STM32F10x_CEC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @addtogroup CEC
+  * @{
+  */
+  
+
+/** @defgroup CEC_Exported_Types
+  * @{
+  */
+   
+/** 
+  * @brief  CEC Init structure definition  
+  */ 
+typedef struct
+{
+  uint16_t CEC_BitTimingMode; /*!< Configures the CEC Bit Timing Error Mode. 
+                               This parameter can be a value of @ref CEC_BitTiming_Mode */
+  uint16_t CEC_BitPeriodMode; /*!< Configures the CEC Bit Period Error Mode. 
+                               This parameter can be a value of @ref CEC_BitPeriod_Mode */
+}CEC_InitTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup CEC_Exported_Constants
+  * @{
+  */ 
+  
+/** @defgroup CEC_BitTiming_Mode 
+  * @{
+  */ 
+#define CEC_BitTimingStdMode                    ((uint16_t)0x00) /*!< Bit timing error Standard Mode */
+#define CEC_BitTimingErrFreeMode                CEC_CFGR_BTEM   /*!< Bit timing error Free Mode */
+
+#define IS_CEC_BIT_TIMING_ERROR_MODE(MODE) (((MODE) == CEC_BitTimingStdMode) || \
+                                            ((MODE) == CEC_BitTimingErrFreeMode))
+/**
+  * @}
+  */
+
+/** @defgroup CEC_BitPeriod_Mode 
+  * @{
+  */ 
+#define CEC_BitPeriodStdMode                    ((uint16_t)0x00) /*!< Bit period error Standard Mode */
+#define CEC_BitPeriodFlexibleMode                CEC_CFGR_BPEM   /*!< Bit period error Flexible Mode */
+
+#define IS_CEC_BIT_PERIOD_ERROR_MODE(MODE) (((MODE) == CEC_BitPeriodStdMode) || \
+                                            ((MODE) == CEC_BitPeriodFlexibleMode))
+/**
+  * @}
+  */ 
+
+
+/** @defgroup CEC_interrupts_definition 
+  * @{
+  */ 
+#define CEC_IT_TERR                              CEC_CSR_TERR
+#define CEC_IT_TBTRF                             CEC_CSR_TBTRF
+#define CEC_IT_RERR                              CEC_CSR_RERR
+#define CEC_IT_RBTF                              CEC_CSR_RBTF
+#define IS_CEC_GET_IT(IT) (((IT) == CEC_IT_TERR) || ((IT) == CEC_IT_TBTRF) || \
+                           ((IT) == CEC_IT_RERR) || ((IT) == CEC_IT_RBTF))
+/**
+  * @}
+  */ 
+
+
+/** @defgroup CEC_Own_Address 
+  * @{
+  */ 
+#define IS_CEC_ADDRESS(ADDRESS) ((ADDRESS) < 0x10)
+/**
+  * @}
+  */ 
+
+/** @defgroup CEC_Prescaler 
+  * @{
+  */ 
+#define IS_CEC_PRESCALER(PRESCALER) ((PRESCALER) <= 0x3FFF)
+
+/**
+  * @}
+  */
+
+/** @defgroup CEC_flags_definition 
+  * @{
+  */
+   
+/** 
+  * @brief  ESR register flags  
+  */ 
+#define CEC_FLAG_BTE                            ((uint32_t)0x10010000)
+#define CEC_FLAG_BPE                            ((uint32_t)0x10020000)
+#define CEC_FLAG_RBTFE                          ((uint32_t)0x10040000)
+#define CEC_FLAG_SBE                            ((uint32_t)0x10080000)
+#define CEC_FLAG_ACKE                           ((uint32_t)0x10100000)
+#define CEC_FLAG_LINE                           ((uint32_t)0x10200000)
+#define CEC_FLAG_TBTFE                          ((uint32_t)0x10400000)
+
+/** 
+  * @brief  CSR register flags  
+  */ 
+#define CEC_FLAG_TEOM                           ((uint32_t)0x00000002)  
+#define CEC_FLAG_TERR                           ((uint32_t)0x00000004)
+#define CEC_FLAG_TBTRF                          ((uint32_t)0x00000008)
+#define CEC_FLAG_RSOM                           ((uint32_t)0x00000010)
+#define CEC_FLAG_REOM                           ((uint32_t)0x00000020)
+#define CEC_FLAG_RERR                           ((uint32_t)0x00000040)
+#define CEC_FLAG_RBTF                           ((uint32_t)0x00000080)
+
+#define IS_CEC_CLEAR_FLAG(FLAG) ((((FLAG) & (uint32_t)0xFFFFFF03) == 0x00) && ((FLAG) != 0x00))
+                               
+#define IS_CEC_GET_FLAG(FLAG) (((FLAG) == CEC_FLAG_BTE) || ((FLAG) == CEC_FLAG_BPE) || \
+                               ((FLAG) == CEC_FLAG_RBTFE) || ((FLAG)== CEC_FLAG_SBE) || \
+                               ((FLAG) == CEC_FLAG_ACKE) || ((FLAG) == CEC_FLAG_LINE) || \
+                               ((FLAG) == CEC_FLAG_TBTFE) || ((FLAG) == CEC_FLAG_TEOM) || \
+                               ((FLAG) == CEC_FLAG_TERR) || ((FLAG) == CEC_FLAG_TBTRF) || \
+                               ((FLAG) == CEC_FLAG_RSOM) || ((FLAG) == CEC_FLAG_REOM) || \
+                               ((FLAG) == CEC_FLAG_RERR) || ((FLAG) == CEC_FLAG_RBTF))
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/** @defgroup CEC_Exported_Macros
+  * @{
+  */
+ 
+/**
+  * @}
+  */
+
+/** @defgroup CEC_Exported_Functions
+  * @{
+  */ 
+void CEC_DeInit(void);
+void CEC_Init(CEC_InitTypeDef* CEC_InitStruct);
+void CEC_Cmd(FunctionalState NewState);
+void CEC_ITConfig(FunctionalState NewState);
+void CEC_OwnAddressConfig(uint8_t CEC_OwnAddress);
+void CEC_SetPrescaler(uint16_t CEC_Prescaler);
+void CEC_SendDataByte(uint8_t Data);
+uint8_t CEC_ReceiveDataByte(void);
+void CEC_StartOfMessage(void);
+void CEC_EndOfMessageCmd(FunctionalState NewState);
+FlagStatus CEC_GetFlagStatus(uint32_t CEC_FLAG);
+void CEC_ClearFlag(uint32_t CEC_FLAG);
+ITStatus CEC_GetITStatus(uint8_t CEC_IT);
+void CEC_ClearITPendingBit(uint16_t CEC_IT);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F10x_CEC_H */
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_crc.c

+/**
+  ******************************************************************************
+  * @file    stm32f10x_crc.c
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file provides all the CRC firmware functions.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_crc.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup CRC 
+  * @brief CRC driver modules
+  * @{
+  */
+
+/** @defgroup CRC_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Private_Defines
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Private_Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Resets the CRC Data register (DR).
+  * @param  None
+  * @retval None
+  */
+void CRC_ResetDR(void)
+{
+  /* Reset CRC generator */
+  CRC->CR = CRC_CR_RESET;
+}
+
+/**
+  * @brief  Computes the 32-bit CRC of a given data word(32-bit).
+  * @param  Data: data word(32-bit) to compute its CRC
+  * @retval 32-bit CRC
+  */
+uint32_t CRC_CalcCRC(uint32_t Data)
+{
+  CRC->DR = Data;
+  
+  return (CRC->DR);
+}
+
+/**
+  * @brief  Computes the 32-bit CRC of a given buffer of data word(32-bit).
+  * @param  pBuffer: pointer to the buffer containing the data to be computed
+  * @param  BufferLength: length of the buffer to be computed					
+  * @retval 32-bit CRC
+  */
+uint32_t CRC_CalcBlockCRC(uint32_t pBuffer[], uint32_t BufferLength)
+{
+  uint32_t index = 0;
+  
+  for(index = 0; index < BufferLength; index++)
+  {
+    CRC->DR = pBuffer[index];
+  }
+  return (CRC->DR);
+}
+
+/**
+  * @brief  Returns the current CRC value.
+  * @param  None
+  * @retval 32-bit CRC
+  */
+uint32_t CRC_GetCRC(void)
+{
+  return (CRC->DR);
+}
+
+/**
+  * @brief  Stores a 8-bit data in the Independent Data(ID) register.
+  * @param  IDValue: 8-bit value to be stored in the ID register 					
+  * @retval None
+  */
+void CRC_SetIDRegister(uint8_t IDValue)
+{
+  CRC->IDR = IDValue;
+}
+
+/**
+  * @brief  Returns the 8-bit data stored in the Independent Data(ID) register
+  * @param  None
+  * @retval 8-bit value of the ID register 
+  */
+uint8_t CRC_GetIDRegister(void)
+{
+  return (CRC->IDR);
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_crc.h

+/**
+  ******************************************************************************
+  * @file    stm32f10x_crc.h
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file contains all the functions prototypes for the CRC firmware 
+  *          library.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_CRC_H
+#define __STM32F10x_CRC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @addtogroup CRC
+  * @{
+  */
+
+/** @defgroup CRC_Exported_Types
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Exported_Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_Exported_Functions
+  * @{
+  */
+
+void CRC_ResetDR(void);
+uint32_t CRC_CalcCRC(uint32_t Data);
+uint32_t CRC_CalcBlockCRC(uint32_t pBuffer[], uint32_t BufferLength);
+uint32_t CRC_GetCRC(void);
+void CRC_SetIDRegister(uint8_t IDValue);
+uint8_t CRC_GetIDRegister(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F10x_CRC_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_dbgmcu.c

+/**
+  ******************************************************************************
+  * @file    stm32f10x_dbgmcu.c
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file provides all the DBGMCU firmware functions.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_dbgmcu.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup DBGMCU 
+  * @brief DBGMCU driver modules
+  * @{
+  */ 
+
+/** @defgroup DBGMCU_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Private_Defines
+  * @{
+  */
+
+#define IDCODE_DEVID_MASK    ((uint32_t)0x00000FFF)
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Private_Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Returns the device revision identifier.
+  * @param  None
+  * @retval Device revision identifier
+  */
+uint32_t DBGMCU_GetREVID(void)
+{
+   return(DBGMCU->IDCODE >> 16);
+}
+
+/**
+  * @brief  Returns the device identifier.
+  * @param  None
+  * @retval Device identifier
+  */
+uint32_t DBGMCU_GetDEVID(void)
+{
+   return(DBGMCU->IDCODE & IDCODE_DEVID_MASK);
+}
+
+/**
+  * @brief  Configures the specified peripheral and low power mode behavior
+  *   when the MCU under Debug mode.
+  * @param  DBGMCU_Periph: specifies the peripheral and low power mode.
+  *   This parameter can be any combination of the following values:
+  *     @arg DBGMCU_SLEEP: Keep debugger connection during SLEEP mode              
+  *     @arg DBGMCU_STOP: Keep debugger connection during STOP mode               
+  *     @arg DBGMCU_STANDBY: Keep debugger connection during STANDBY mode            
+  *     @arg DBGMCU_IWDG_STOP: Debug IWDG stopped when Core is halted          
+  *     @arg DBGMCU_WWDG_STOP: Debug WWDG stopped when Core is halted          
+  *     @arg DBGMCU_TIM1_STOP: TIM1 counter stopped when Core is halted          
+  *     @arg DBGMCU_TIM2_STOP: TIM2 counter stopped when Core is halted          
+  *     @arg DBGMCU_TIM3_STOP: TIM3 counter stopped when Core is halted          
+  *     @arg DBGMCU_TIM4_STOP: TIM4 counter stopped when Core is halted          
+  *     @arg DBGMCU_CAN1_STOP: Debug CAN2 stopped when Core is halted           
+  *     @arg DBGMCU_I2C1_SMBUS_TIMEOUT: I2C1 SMBUS timeout mode stopped when Core is halted
+  *     @arg DBGMCU_I2C2_SMBUS_TIMEOUT: I2C2 SMBUS timeout mode stopped when Core is halted
+  *     @arg DBGMCU_TIM5_STOP: TIM5 counter stopped when Core is halted          
+  *     @arg DBGMCU_TIM6_STOP: TIM6 counter stopped when Core is halted          
+  *     @arg DBGMCU_TIM7_STOP: TIM7 counter stopped when Core is halted          
+  *     @arg DBGMCU_TIM8_STOP: TIM8 counter stopped when Core is halted
+  *     @arg DBGMCU_CAN2_STOP: Debug CAN2 stopped when Core is halted 
+  *     @arg DBGMCU_TIM15_STOP: TIM15 counter stopped when Core is halted
+  *     @arg DBGMCU_TIM16_STOP: TIM16 counter stopped when Core is halted
+  *     @arg DBGMCU_TIM17_STOP: TIM17 counter stopped when Core is halted                
+  *     @arg DBGMCU_TIM9_STOP: TIM9 counter stopped when Core is halted
+  *     @arg DBGMCU_TIM10_STOP: TIM10 counter stopped when Core is halted
+  *     @arg DBGMCU_TIM11_STOP: TIM11 counter stopped when Core is halted
+  *     @arg DBGMCU_TIM12_STOP: TIM12 counter stopped when Core is halted
+  *     @arg DBGMCU_TIM13_STOP: TIM13 counter stopped when Core is halted
+  *     @arg DBGMCU_TIM14_STOP: TIM14 counter stopped when Core is halted
+  * @param  NewState: new state of the specified peripheral in Debug mode.
+  *   This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void DBGMCU_Config(uint32_t DBGMCU_Periph, FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_DBGMCU_PERIPH(DBGMCU_Periph));
+  assert_param(IS_FUNCTIONAL_STATE(NewState));
+
+  if (NewState != DISABLE)
+  {
+    DBGMCU->CR |= DBGMCU_Periph;
+  }
+  else
+  {
+    DBGMCU->CR &= ~DBGMCU_Periph;
+  }
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_dbgmcu.h

+/**
+  ******************************************************************************
+  * @file    stm32f10x_dbgmcu.h
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file contains all the functions prototypes for the DBGMCU 
+  *          firmware library.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_DBGMCU_H
+#define __STM32F10x_DBGMCU_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @addtogroup DBGMCU
+  * @{
+  */
+
+/** @defgroup DBGMCU_Exported_Types
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Exported_Constants
+  * @{
+  */
+
+#define DBGMCU_SLEEP                 ((uint32_t)0x00000001)
+#define DBGMCU_STOP                  ((uint32_t)0x00000002)
+#define DBGMCU_STANDBY               ((uint32_t)0x00000004)
+#define DBGMCU_IWDG_STOP             ((uint32_t)0x00000100)
+#define DBGMCU_WWDG_STOP             ((uint32_t)0x00000200)
+#define DBGMCU_TIM1_STOP             ((uint32_t)0x00000400)
+#define DBGMCU_TIM2_STOP             ((uint32_t)0x00000800)
+#define DBGMCU_TIM3_STOP             ((uint32_t)0x00001000)
+#define DBGMCU_TIM4_STOP             ((uint32_t)0x00002000)
+#define DBGMCU_CAN1_STOP             ((uint32_t)0x00004000)
+#define DBGMCU_I2C1_SMBUS_TIMEOUT    ((uint32_t)0x00008000)
+#define DBGMCU_I2C2_SMBUS_TIMEOUT    ((uint32_t)0x00010000)
+#define DBGMCU_TIM8_STOP             ((uint32_t)0x00020000)
+#define DBGMCU_TIM5_STOP             ((uint32_t)0x00040000)
+#define DBGMCU_TIM6_STOP             ((uint32_t)0x00080000)
+#define DBGMCU_TIM7_STOP             ((uint32_t)0x00100000)
+#define DBGMCU_CAN2_STOP             ((uint32_t)0x00200000)
+#define DBGMCU_TIM15_STOP            ((uint32_t)0x00400000)
+#define DBGMCU_TIM16_STOP            ((uint32_t)0x00800000)
+#define DBGMCU_TIM17_STOP            ((uint32_t)0x01000000)
+#define DBGMCU_TIM12_STOP            ((uint32_t)0x02000000)
+#define DBGMCU_TIM13_STOP            ((uint32_t)0x04000000)
+#define DBGMCU_TIM14_STOP            ((uint32_t)0x08000000)
+#define DBGMCU_TIM9_STOP             ((uint32_t)0x10000000)
+#define DBGMCU_TIM10_STOP            ((uint32_t)0x20000000)
+#define DBGMCU_TIM11_STOP            ((uint32_t)0x40000000)
+                                              
+#define IS_DBGMCU_PERIPH(PERIPH) ((((PERIPH) & 0x800000F8) == 0x00) && ((PERIPH) != 0x00))
+/**
+  * @}
+  */ 
+
+/** @defgroup DBGMCU_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup DBGMCU_Exported_Functions
+  * @{
+  */
+
+uint32_t DBGMCU_GetREVID(void);
+uint32_t DBGMCU_GetDEVID(void);
+void DBGMCU_Config(uint32_t DBGMCU_Periph, FunctionalState NewState);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F10x_DBGMCU_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_exti.c

+/**
+  ******************************************************************************
+  * @file    stm32f10x_exti.c
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file provides all the EXTI firmware functions.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_exti.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup EXTI 
+  * @brief EXTI driver modules
+  * @{
+  */
+
+/** @defgroup EXTI_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Private_Defines
+  * @{
+  */
+
+#define EXTI_LINENONE    ((uint32_t)0x00000)  /* No interrupt selected */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Private_Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Deinitializes the EXTI peripheral registers to their default reset values.
+  * @param  None
+  * @retval None
+  */
+void EXTI_DeInit(void)
+{
+  EXTI->IMR = 0x00000000;
+  EXTI->EMR = 0x00000000;
+  EXTI->RTSR = 0x00000000; 
+  EXTI->FTSR = 0x00000000; 
+  EXTI->PR = 0x000FFFFF;
+}
+
+/**
+  * @brief  Initializes the EXTI peripheral according to the specified
+  *         parameters in the EXTI_InitStruct.
+  * @param  EXTI_InitStruct: pointer to a EXTI_InitTypeDef structure
+  *         that contains the configuration information for the EXTI peripheral.
+  * @retval None
+  */
+void EXTI_Init(EXTI_InitTypeDef* EXTI_InitStruct)
+{
+  uint32_t tmp = 0;
+
+  /* Check the parameters */
+  assert_param(IS_EXTI_MODE(EXTI_InitStruct->EXTI_Mode));
+  assert_param(IS_EXTI_TRIGGER(EXTI_InitStruct->EXTI_Trigger));
+  assert_param(IS_EXTI_LINE(EXTI_InitStruct->EXTI_Line));  
+  assert_param(IS_FUNCTIONAL_STATE(EXTI_InitStruct->EXTI_LineCmd));
+
+  tmp = (uint32_t)EXTI_BASE;
+     
+  if (EXTI_InitStruct->EXTI_LineCmd != DISABLE)
+  {
+    /* Clear EXTI line configuration */
+    EXTI->IMR &= ~EXTI_InitStruct->EXTI_Line;
+    EXTI->EMR &= ~EXTI_InitStruct->EXTI_Line;
+    
+    tmp += EXTI_InitStruct->EXTI_Mode;
+
+    *(__IO uint32_t *) tmp |= EXTI_InitStruct->EXTI_Line;
+
+    /* Clear Rising Falling edge configuration */
+    EXTI->RTSR &= ~EXTI_InitStruct->EXTI_Line;
+    EXTI->FTSR &= ~EXTI_InitStruct->EXTI_Line;
+    
+    /* Select the trigger for the selected external interrupts */
+    if (EXTI_InitStruct->EXTI_Trigger == EXTI_Trigger_Rising_Falling)
+    {
+      /* Rising Falling edge */
+      EXTI->RTSR |= EXTI_InitStruct->EXTI_Line;
+      EXTI->FTSR |= EXTI_InitStruct->EXTI_Line;
+    }
+    else
+    {
+      tmp = (uint32_t)EXTI_BASE;
+      tmp += EXTI_InitStruct->EXTI_Trigger;
+
+      *(__IO uint32_t *) tmp |= EXTI_InitStruct->EXTI_Line;
+    }
+  }
+  else
+  {
+    tmp += EXTI_InitStruct->EXTI_Mode;
+
+    /* Disable the selected external lines */
+    *(__IO uint32_t *) tmp &= ~EXTI_InitStruct->EXTI_Line;
+  }
+}
+
+/**
+  * @brief  Fills each EXTI_InitStruct member with its reset value.
+  * @param  EXTI_InitStruct: pointer to a EXTI_InitTypeDef structure which will
+  *         be initialized.
+  * @retval None
+  */
+void EXTI_StructInit(EXTI_InitTypeDef* EXTI_InitStruct)
+{
+  EXTI_InitStruct->EXTI_Line = EXTI_LINENONE;
+  EXTI_InitStruct->EXTI_Mode = EXTI_Mode_Interrupt;
+  EXTI_InitStruct->EXTI_Trigger = EXTI_Trigger_Falling;
+  EXTI_InitStruct->EXTI_LineCmd = DISABLE;
+}
+
+/**
+  * @brief  Generates a Software interrupt.
+  * @param  EXTI_Line: specifies the EXTI lines to be enabled or disabled.
+  *   This parameter can be any combination of EXTI_Linex where x can be (0..19).
+  * @retval None
+  */
+void EXTI_GenerateSWInterrupt(uint32_t EXTI_Line)
+{
+  /* Check the parameters */
+  assert_param(IS_EXTI_LINE(EXTI_Line));
+  
+  EXTI->SWIER |= EXTI_Line;
+}
+
+/**
+  * @brief  Checks whether the specified EXTI line flag is set or not.
+  * @param  EXTI_Line: specifies the EXTI line flag to check.
+  *   This parameter can be:
+  *     @arg EXTI_Linex: External interrupt line x where x(0..19)
+  * @retval The new state of EXTI_Line (SET or RESET).
+  */
+FlagStatus EXTI_GetFlagStatus(uint32_t EXTI_Line)
+{
+  FlagStatus bitstatus = RESET;
+  /* Check the parameters */
+  assert_param(IS_GET_EXTI_LINE(EXTI_Line));
+  
+  if ((EXTI->PR & EXTI_Line) != (uint32_t)RESET)
+  {
+    bitstatus = SET;
+  }
+  else
+  {
+    bitstatus = RESET;
+  }
+  return bitstatus;
+}
+
+/**
+  * @brief  Clears the EXTI's line pending flags.
+  * @param  EXTI_Line: specifies the EXTI lines flags to clear.
+  *   This parameter can be any combination of EXTI_Linex where x can be (0..19).
+  * @retval None
+  */
+void EXTI_ClearFlag(uint32_t EXTI_Line)
+{
+  /* Check the parameters */
+  assert_param(IS_EXTI_LINE(EXTI_Line));
+  
+  EXTI->PR = EXTI_Line;
+}
+
+/**
+  * @brief  Checks whether the specified EXTI line is asserted or not.
+  * @param  EXTI_Line: specifies the EXTI line to check.
+  *   This parameter can be:
+  *     @arg EXTI_Linex: External interrupt line x where x(0..19)
+  * @retval The new state of EXTI_Line (SET or RESET).
+  */
+ITStatus EXTI_GetITStatus(uint32_t EXTI_Line)
+{
+  ITStatus bitstatus = RESET;
+  uint32_t enablestatus = 0;
+  /* Check the parameters */
+  assert_param(IS_GET_EXTI_LINE(EXTI_Line));
+  
+  enablestatus =  EXTI->IMR & EXTI_Line;
+  if (((EXTI->PR & EXTI_Line) != (uint32_t)RESET) && (enablestatus != (uint32_t)RESET))
+  {
+    bitstatus = SET;
+  }
+  else
+  {
+    bitstatus = RESET;
+  }
+  return bitstatus;
+}
+
+/**
+  * @brief  Clears the EXTI's line pending bits.
+  * @param  EXTI_Line: specifies the EXTI lines to clear.
+  *   This parameter can be any combination of EXTI_Linex where x can be (0..19).
+  * @retval None
+  */
+void EXTI_ClearITPendingBit(uint32_t EXTI_Line)
+{
+  /* Check the parameters */
+  assert_param(IS_EXTI_LINE(EXTI_Line));
+  
+  EXTI->PR = EXTI_Line;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_exti.h

+/**
+  ******************************************************************************
+  * @file    stm32f10x_exti.h
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file contains all the functions prototypes for the EXTI firmware
+  *          library.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_EXTI_H
+#define __STM32F10x_EXTI_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @addtogroup EXTI
+  * @{
+  */
+
+/** @defgroup EXTI_Exported_Types
+  * @{
+  */
+
+/** 
+  * @brief  EXTI mode enumeration  
+  */
+
+typedef enum
+{
+  EXTI_Mode_Interrupt = 0x00,
+  EXTI_Mode_Event = 0x04
+}EXTIMode_TypeDef;
+
+#define IS_EXTI_MODE(MODE) (((MODE) == EXTI_Mode_Interrupt) || ((MODE) == EXTI_Mode_Event))
+
+/** 
+  * @brief  EXTI Trigger enumeration  
+  */
+
+typedef enum
+{
+  EXTI_Trigger_Rising = 0x08,
+  EXTI_Trigger_Falling = 0x0C,  
+  EXTI_Trigger_Rising_Falling = 0x10
+}EXTITrigger_TypeDef;
+
+#define IS_EXTI_TRIGGER(TRIGGER) (((TRIGGER) == EXTI_Trigger_Rising) || \
+                                  ((TRIGGER) == EXTI_Trigger_Falling) || \
+                                  ((TRIGGER) == EXTI_Trigger_Rising_Falling))
+/** 
+  * @brief  EXTI Init Structure definition  
+  */
+
+typedef struct
+{
+  uint32_t EXTI_Line;               /*!< Specifies the EXTI lines to be enabled or disabled.
+                                         This parameter can be any combination of @ref EXTI_Lines */
+   
+  EXTIMode_TypeDef EXTI_Mode;       /*!< Specifies the mode for the EXTI lines.
+                                         This parameter can be a value of @ref EXTIMode_TypeDef */
+
+  EXTITrigger_TypeDef EXTI_Trigger; /*!< Specifies the trigger signal active edge for the EXTI lines.
+                                         This parameter can be a value of @ref EXTIMode_TypeDef */
+
+  FunctionalState EXTI_LineCmd;     /*!< Specifies the new state of the selected EXTI lines.
+                                         This parameter can be set either to ENABLE or DISABLE */ 
+}EXTI_InitTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Exported_Constants
+  * @{
+  */
+
+/** @defgroup EXTI_Lines 
+  * @{
+  */
+
+#define EXTI_Line0       ((uint32_t)0x00001)  /*!< External interrupt line 0 */
+#define EXTI_Line1       ((uint32_t)0x00002)  /*!< External interrupt line 1 */
+#define EXTI_Line2       ((uint32_t)0x00004)  /*!< External interrupt line 2 */
+#define EXTI_Line3       ((uint32_t)0x00008)  /*!< External interrupt line 3 */
+#define EXTI_Line4       ((uint32_t)0x00010)  /*!< External interrupt line 4 */
+#define EXTI_Line5       ((uint32_t)0x00020)  /*!< External interrupt line 5 */
+#define EXTI_Line6       ((uint32_t)0x00040)  /*!< External interrupt line 6 */
+#define EXTI_Line7       ((uint32_t)0x00080)  /*!< External interrupt line 7 */
+#define EXTI_Line8       ((uint32_t)0x00100)  /*!< External interrupt line 8 */
+#define EXTI_Line9       ((uint32_t)0x00200)  /*!< External interrupt line 9 */
+#define EXTI_Line10      ((uint32_t)0x00400)  /*!< External interrupt line 10 */
+#define EXTI_Line11      ((uint32_t)0x00800)  /*!< External interrupt line 11 */
+#define EXTI_Line12      ((uint32_t)0x01000)  /*!< External interrupt line 12 */
+#define EXTI_Line13      ((uint32_t)0x02000)  /*!< External interrupt line 13 */
+#define EXTI_Line14      ((uint32_t)0x04000)  /*!< External interrupt line 14 */
+#define EXTI_Line15      ((uint32_t)0x08000)  /*!< External interrupt line 15 */
+#define EXTI_Line16      ((uint32_t)0x10000)  /*!< External interrupt line 16 Connected to the PVD Output */
+#define EXTI_Line17      ((uint32_t)0x20000)  /*!< External interrupt line 17 Connected to the RTC Alarm event */
+#define EXTI_Line18      ((uint32_t)0x40000)  /*!< External interrupt line 18 Connected to the USB Device/USB OTG FS
+                                                   Wakeup from suspend event */                                    
+#define EXTI_Line19      ((uint32_t)0x80000)  /*!< External interrupt line 19 Connected to the Ethernet Wakeup event */
+                                          
+#define IS_EXTI_LINE(LINE) ((((LINE) & (uint32_t)0xFFF00000) == 0x00) && ((LINE) != (uint16_t)0x00))
+#define IS_GET_EXTI_LINE(LINE) (((LINE) == EXTI_Line0) || ((LINE) == EXTI_Line1) || \
+                            ((LINE) == EXTI_Line2) || ((LINE) == EXTI_Line3) || \
+                            ((LINE) == EXTI_Line4) || ((LINE) == EXTI_Line5) || \
+                            ((LINE) == EXTI_Line6) || ((LINE) == EXTI_Line7) || \
+                            ((LINE) == EXTI_Line8) || ((LINE) == EXTI_Line9) || \
+                            ((LINE) == EXTI_Line10) || ((LINE) == EXTI_Line11) || \
+                            ((LINE) == EXTI_Line12) || ((LINE) == EXTI_Line13) || \
+                            ((LINE) == EXTI_Line14) || ((LINE) == EXTI_Line15) || \
+                            ((LINE) == EXTI_Line16) || ((LINE) == EXTI_Line17) || \
+                            ((LINE) == EXTI_Line18) || ((LINE) == EXTI_Line19))
+
+                    
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Exported_Functions
+  * @{
+  */
+
+void EXTI_DeInit(void);
+void EXTI_Init(EXTI_InitTypeDef* EXTI_InitStruct);
+void EXTI_StructInit(EXTI_InitTypeDef* EXTI_InitStruct);
+void EXTI_GenerateSWInterrupt(uint32_t EXTI_Line);
+FlagStatus EXTI_GetFlagStatus(uint32_t EXTI_Line);
+void EXTI_ClearFlag(uint32_t EXTI_Line);
+ITStatus EXTI_GetITStatus(uint32_t EXTI_Line);
+void EXTI_ClearITPendingBit(uint32_t EXTI_Line);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F10x_EXTI_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_iwdg.c

+/**
+  ******************************************************************************
+  * @file    stm32f10x_iwdg.c
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file provides all the IWDG firmware functions.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_iwdg.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup IWDG 
+  * @brief IWDG driver modules
+  * @{
+  */ 
+
+/** @defgroup IWDG_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Private_Defines
+  * @{
+  */ 
+
+/* ---------------------- IWDG registers bit mask ----------------------------*/
+
+/* KR register bit mask */
+#define KR_KEY_Reload    ((uint16_t)0xAAAA)
+#define KR_KEY_Enable    ((uint16_t)0xCCCC)
+
+/**
+  * @}
+  */ 
+
+/** @defgroup IWDG_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Private_Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Enables or disables write access to IWDG_PR and IWDG_RLR registers.
+  * @param  IWDG_WriteAccess: new state of write access to IWDG_PR and IWDG_RLR registers.
+  *   This parameter can be one of the following values:
+  *     @arg IWDG_WriteAccess_Enable: Enable write access to IWDG_PR and IWDG_RLR registers
+  *     @arg IWDG_WriteAccess_Disable: Disable write access to IWDG_PR and IWDG_RLR registers
+  * @retval None
+  */
+void IWDG_WriteAccessCmd(uint16_t IWDG_WriteAccess)
+{
+  /* Check the parameters */
+  assert_param(IS_IWDG_WRITE_ACCESS(IWDG_WriteAccess));
+  IWDG->KR = IWDG_WriteAccess;
+}
+
+/**
+  * @brief  Sets IWDG Prescaler value.
+  * @param  IWDG_Prescaler: specifies the IWDG Prescaler value.
+  *   This parameter can be one of the following values:
+  *     @arg IWDG_Prescaler_4: IWDG prescaler set to 4
+  *     @arg IWDG_Prescaler_8: IWDG prescaler set to 8
+  *     @arg IWDG_Prescaler_16: IWDG prescaler set to 16
+  *     @arg IWDG_Prescaler_32: IWDG prescaler set to 32
+  *     @arg IWDG_Prescaler_64: IWDG prescaler set to 64
+  *     @arg IWDG_Prescaler_128: IWDG prescaler set to 128
+  *     @arg IWDG_Prescaler_256: IWDG prescaler set to 256
+  * @retval None
+  */
+void IWDG_SetPrescaler(uint8_t IWDG_Prescaler)
+{
+  /* Check the parameters */
+  assert_param(IS_IWDG_PRESCALER(IWDG_Prescaler));
+  IWDG->PR = IWDG_Prescaler;
+}
+
+/**
+  * @brief  Sets IWDG Reload value.
+  * @param  Reload: specifies the IWDG Reload value.
+  *   This parameter must be a number between 0 and 0x0FFF.
+  * @retval None
+  */
+void IWDG_SetReload(uint16_t Reload)
+{
+  /* Check the parameters */
+  assert_param(IS_IWDG_RELOAD(Reload));
+  IWDG->RLR = Reload;
+}
+
+/**
+  * @brief  Reloads IWDG counter with value defined in the reload register
+  *   (write access to IWDG_PR and IWDG_RLR registers disabled).
+  * @param  None
+  * @retval None
+  */
+void IWDG_ReloadCounter(void)
+{
+  IWDG->KR = KR_KEY_Reload;
+}
+
+/**
+  * @brief  Enables IWDG (write access to IWDG_PR and IWDG_RLR registers disabled).
+  * @param  None
+  * @retval None
+  */
+void IWDG_Enable(void)
+{
+  IWDG->KR = KR_KEY_Enable;
+}
+
+/**
+  * @brief  Checks whether the specified IWDG flag is set or not.
+  * @param  IWDG_FLAG: specifies the flag to check.
+  *   This parameter can be one of the following values:
+  *     @arg IWDG_FLAG_PVU: Prescaler Value Update on going
+  *     @arg IWDG_FLAG_RVU: Reload Value Update on going
+  * @retval The new state of IWDG_FLAG (SET or RESET).
+  */
+FlagStatus IWDG_GetFlagStatus(uint16_t IWDG_FLAG)
+{
+  FlagStatus bitstatus = RESET;
+  /* Check the parameters */
+  assert_param(IS_IWDG_FLAG(IWDG_FLAG));
+  if ((IWDG->SR & IWDG_FLAG) != (uint32_t)RESET)
+  {
+    bitstatus = SET;
+  }
+  else
+  {
+    bitstatus = RESET;
+  }
+  /* Return the flag status */
+  return bitstatus;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_iwdg.h

+/**
+  ******************************************************************************
+  * @file    stm32f10x_iwdg.h
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file contains all the functions prototypes for the IWDG 
+  *          firmware library.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F10x_IWDG_H
+#define __STM32F10x_IWDG_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @addtogroup IWDG
+  * @{
+  */
+
+/** @defgroup IWDG_Exported_Types
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Exported_Constants
+  * @{
+  */
+
+/** @defgroup IWDG_WriteAccess
+  * @{
+  */
+
+#define IWDG_WriteAccess_Enable     ((uint16_t)0x5555)
+#define IWDG_WriteAccess_Disable    ((uint16_t)0x0000)
+#define IS_IWDG_WRITE_ACCESS(ACCESS) (((ACCESS) == IWDG_WriteAccess_Enable) || \
+                                      ((ACCESS) == IWDG_WriteAccess_Disable))
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_prescaler 
+  * @{
+  */
+
+#define IWDG_Prescaler_4            ((uint8_t)0x00)
+#define IWDG_Prescaler_8            ((uint8_t)0x01)
+#define IWDG_Prescaler_16           ((uint8_t)0x02)
+#define IWDG_Prescaler_32           ((uint8_t)0x03)
+#define IWDG_Prescaler_64           ((uint8_t)0x04)
+#define IWDG_Prescaler_128          ((uint8_t)0x05)
+#define IWDG_Prescaler_256          ((uint8_t)0x06)
+#define IS_IWDG_PRESCALER(PRESCALER) (((PRESCALER) == IWDG_Prescaler_4)  || \
+                                      ((PRESCALER) == IWDG_Prescaler_8)  || \
+                                      ((PRESCALER) == IWDG_Prescaler_16) || \
+                                      ((PRESCALER) == IWDG_Prescaler_32) || \
+                                      ((PRESCALER) == IWDG_Prescaler_64) || \
+                                      ((PRESCALER) == IWDG_Prescaler_128)|| \
+                                      ((PRESCALER) == IWDG_Prescaler_256))
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Flag 
+  * @{
+  */
+
+#define IWDG_FLAG_PVU               ((uint16_t)0x0001)
+#define IWDG_FLAG_RVU               ((uint16_t)0x0002)
+#define IS_IWDG_FLAG(FLAG) (((FLAG) == IWDG_FLAG_PVU) || ((FLAG) == IWDG_FLAG_RVU))
+#define IS_IWDG_RELOAD(RELOAD) ((RELOAD) <= 0xFFF)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Exported_Functions
+  * @{
+  */
+
+void IWDG_WriteAccessCmd(uint16_t IWDG_WriteAccess);
+void IWDG_SetPrescaler(uint8_t IWDG_Prescaler);
+void IWDG_SetReload(uint16_t Reload);
+void IWDG_ReloadCounter(void);
+void IWDG_Enable(void);
+FlagStatus IWDG_GetFlagStatus(uint16_t IWDG_FLAG);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F10x_IWDG_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

Library/stm32f10x_pwr.c

+/**
+  ******************************************************************************
+  * @file    stm32f10x_pwr.c
+  * @author  MCD Application Team
+  * @version V3.5.0
+  * @date    11-March-2011
+  * @brief   This file provides all the PWR firmware functions.
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f10x_pwr.h"
+#include "stm32f10x_rcc.h"
+
+/** @addtogroup STM32F10x_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup PWR 
+  * @brief PWR driver modules
+  * @{
+  */ 
+
+/** @defgroup PWR_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Private_Defines
+  * @{
+  */
+
+/* --------- PWR registers bit address in the alias region ---------- */
+#define PWR_OFFSET               (PWR_BASE - PERIPH_BASE)
+
+/* --- CR Register ---*/
+
+/* Alias word address of DBP bit */
+#define CR_OFFSET                (PWR_OFFSET + 0x00)
+#define DBP_BitNumber            0x08
+#define CR_DBP_BB                (PERIPH_BB_BASE + (CR_OFFSET * 32) + (DBP_BitNumber * 4))
+
+/* Alias word address of PVDE bit */
+#define PVDE_BitNumber           0x04
+#define CR_PVDE_BB               (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PVDE_BitNumber * 4))
+
+/* --- CSR Register ---*/
+
+/* Alias word address of EWUP bit */
+#define CSR_OFFSET               (PWR_OFFSET + 0x04)
+#define EWUP_BitNumber           0x08
+#define CSR_EWUP_BB              (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (EWUP_BitNumber * 4))
+
+/* ------------------ PWR registers bit mask ------------------------ */
+
+/* CR register bit mask */
+#define CR_DS_MASK               ((uint32_t)0xFFFFFFFC)
+#define CR_PLS_MASK              ((uint32_t)0xFFFFFF1F)
+
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Private_Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Deinitializes the PWR peripheral registers to their default reset values.
+  * @param  None
+  * @retval None
+  */
+void PWR_DeInit(void)
+{
+  RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, ENABLE);
+  RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, DISABLE);
+}
+
+/**
+  * @brief  Enables or disables access to the RTC and backup registers.
+  * @param  NewState: new state of the access to the RTC and backup registers.
+  *   This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void PWR_BackupAccessCmd(FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NewState));
+  *(__IO uint32_t *) CR_DBP_BB = (uint32_t)NewState;
+}
+
+/**
+  * @brief  Enables or disables the Power Voltage Detector(PVD).
+  * @param  NewState: new state of the PVD.
+  *   This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void PWR_PVDCmd(FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NewState));
+  *(__IO uint32_t *) CR_PVDE_BB = (uint32_t)NewState;
+}
+
+/**
+  * @brief  Configures the voltage threshold detected by the Power Voltage Detector(PVD).
+  * @param  PWR_PVDLevel: specifies the PVD detection level
+  *   This parameter can be one of the following values:
+  *     @arg PWR_PVDLevel_2V2: PVD detection level set to 2.2V
+  *     @arg PWR_PVDLevel_2V3: PVD detection level set to 2.3V
+  *     @arg PWR_PVDLevel_2V4: PVD detection level set to 2.4V
+  *     @arg PWR_PVDLevel_2V5: PVD detection level set to 2.5V
+  *     @arg PWR_PVDLevel_2V6: PVD detection level set to 2.6V
+  *     @arg PWR_PVDLevel_2V7: PVD detection level set to 2.7V
+  *     @arg PWR_PVDLevel_2V8: PVD detection level set to 2.8V
+  *     @arg PWR_PVDLevel_2V9: PVD detection level set to 2.9V
+  * @retval None
+  */
+void PWR_PVDLevelConfig(uint32_t PWR_PVDLevel)
+{
+  uint32_t tmpreg = 0;
+  /* Check the parameters */
+  assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));
+  tmpreg = PWR->CR;
+  /* Clear PLS[7:5] bits */
+  tmpreg &= CR_PLS_MASK;
+  /* Set PLS[7:5] bits according to PWR_PVDLevel value */
+  tmpreg |= PWR_PVDLevel;
+  /* Store the new value */
+  PWR->CR = tmpreg;
+}
+
+/**
+  * @brief  Enables or disables the WakeUp Pin functionality.
+  * @param  NewState: new state of the WakeUp Pin functionality.
+  *   This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void PWR_WakeUpPinCmd(FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NewState));
+  *(__IO uint32_t *) CSR_EWUP_BB = (uint32_t)NewState;
+}
+
+/**
+  * @brief  Enters STOP mode.
+  * @param  PWR_Regulator: specifies the regulator state in STOP mode.
+  *   This parameter can be one of the following values:
+  *     @arg PWR_Regulator_ON: STOP mode with regulator ON
+  *     @arg PWR_Regulator_LowPower: STOP mode with regulator in low power mode
+  * @param  PWR_STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction.
+  *   This parameter can be one of the following values:
+  *     @arg PWR_STOPEntry_WFI: enter STOP mode with WFI instruction
+  *     @arg PWR_STOPEntry_WFE: enter STOP mode with WFE instruction
+  * @retval None
+  */
+void PWR_EnterSTOPMode(uint32_t PWR_Regulator, uint8_t PWR_STOPEntry)
+{
+  uint32_t tmpreg = 0;
+  /* Check the parameters */
+  assert_param(IS_PWR_REGULATOR(PWR_Regulator));
+  assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));
+  
+  /* Select the regulator state in STOP mode ---------------------------------*/
+  tmpreg = PWR->CR;
+  /* Clear PDDS and LPDS bits */
+  tmpreg &= CR_DS_MASK;
+  /* Set LPDS bit according to PWR_Regulator value */
+  tmpreg |= PWR_Regulator;
+  /* Store the new value */
+  PWR->CR = tmpreg;
+  /* Set SLEEPDEEP bit of Cortex System Control Register */
+  SCB->SCR |= SCB_SCR_SLEEPDEEP;
+  
+  /* Select STOP mode entry --------------------------------------------------*/
+  if(PWR_STOPEntry == PWR_STOPEntry_WFI)
+  {   
+    /* Request Wait For Interrupt */
+    __WFI();
+  }
+  else
+  {
+    /* Request Wait For Event */
+    __WFE();
+  }
+  
+  /* Reset SLEEPDEEP bit of Cortex System Control Register */
+  SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP);  
+}
+
+/**
+  * @brief  Enters STANDBY mode.
+  * @param  None
+  * @retval None
+  */
+void PWR_EnterSTANDBYMode(void)
+{
+  /* Clear Wake-up flag */
+  PWR->CR |= PWR_CR_CWUF;
+  /* Select STANDBY mode */
+  PWR->CR |= PWR_CR_PDDS;
+  /* Set SLEEPDEEP bit of Cortex System Control Register */
+  SCB->SCR |= SCB_SCR_SLEEPDEEP;
+/* This option is used to ensure that store operations are completed */
+#if defined ( __CC_ARM   )
+  __force_stores();
+#endif
+  /* Request Wait For Interrupt */
+  __WFI();
+}
+
+/**
+  * @brief  Checks whether the specified PWR flag is set or not.
+  * @param  PWR_FLAG: specifies the flag to check.
+  *   This parameter can be one of the following values:
+  *     @arg PWR_FLAG_WU: Wake Up flag
+  *     @arg PWR_FLAG_SB: StandBy flag
+  *     @arg PWR_FLAG_PVDO: PVD Output
+  * @retval The new state of PWR_FLAG (SET or RESET).
+  */
+FlagStatus PWR_GetFlagStatus(uint32_t PWR_FLAG)
+{
+  FlagStatus bitstatus = RESET;
+  /* Check the parameters */
+  assert_param(IS_PWR_GET_FLAG(PWR_FLAG));
+  
+  if ((PWR->CSR & PWR_FLAG) != (uint32_t)RESET)
+  {
+    bitstatus = SET;
+  }
+  else
+  {
+    bitstatus = RESET;
+  }
+  /* Return the flag status */
+  return bitstatus;
+}
+
+/**
+  * @brief  Clears the PWR's pending flags.
+  * @param  PWR_FLAG: specifies the flag to clear.
+  *   This parameter can be one of the following values:
+  *     @arg PWR_FLAG_WU: Wake Up flag
+  *     @arg PWR_FLAG_SB: StandBy flag
+  * @retval None
+  */
+void PWR_ClearFlag(uint32_t PWR_FLAG)
+{
+  /* Check the parameters */
+  assert_param(IS_PWR_CLEAR_FLAG(PWR_FLAG));
+         
+  PWR->CR |=  PWR_FLAG << 2;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/